Asko D1776 빠른 시작 매뉴얼 - 페이지 2
{카테고리_이름} Asko D1776에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko D1776 2 페이지. User manual use & care guide general fr (french version)
Asko D1776에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (12 페이지), 기획 및 디자인 매뉴얼 (19 페이지), 사용 및 관리 매뉴얼 (12 페이지), 기획 및 디자인 매뉴얼 (15 페이지), (스페인어) Uso Y Cuidado (12 페이지), (프랑스어) Manuel D'utilisation Et D'entretien (12 페이지)
페이지 인쇄QUICK START PROCEDURES
QUICK START PROCEDURES
1. Load the dishwasher. (There's no need to pre-rinse. Simply scrape off large food particles before
you load the dishware.)
2. After you've pushed the baskets back inside the unit, manually rotate the upper and lower spray
arms to be sure they turn freely. Rearrange any item that blocks the wash arms.
3. Make sure there is rinse aid in the dispenser. Add rinse aid, if needed.
4. Add automatic dishwashing detergent and close the dispenser cover. (See "Amount of Dishwashing
Detergent to Use" below.)
5. Close the door securely. (You should hear it click shut.)
6. Press the touchpad for the desired program and, if desired, the Heat dry option. The red indicator
light for the program you select will come on and the dishwasher will start.
LED WINDOW DISPLAYS
LED WINDOW DISPLAYS
Program Time
Program Time
When a program starts, the LED displays the time it took that program to run last time. As the program runs, the LED displays the remaining
time. If the time exceeds an hour, the display alternates between the hour and minutes remaining. The hour is designated by an h (e.g., 1h).
The program times may not always be the same because of variations in the household hot water temperature. The dishwasher heats
the water to the proper temperature for the program selected, so if the temperature of the water entering your dishwasher is too low, the
dishwasher will run longer because it takes longer to heat the water. Raising your water heater setting could help to shorten the cycle
times. If this doesn't help, call the ASKO Advisory Center.
Fault Codes
Fault Codes
The LED window displays three fault codes, as illustrated below.
Indicates a fault in the heater. Call your local service
technician.
Indicates high water level in the machine. Call the ASKO
Advisory Center.
NOTE: When the LED displays three dashed lines, this simply means the door isn't closed completely.
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
We recommend that you use only unscented, granular automatic dishwashing detergent. Generally, one tablespoon of detergent is
needed for a normal wash load. More heavily soiled items, however, may need more detergent. Also, the amount of detergent needed
can vary due to differences in water hardness. The harder the water, the more detergent you may need. (See page 5.) In any case, you
should never use more than three tablespoons of detergent.
COMMONLY ASKED QUESTIONS
COMMONLY ASKED QUESTIONS
1)
Where do I put the prewash detergent?
2)
Where do I put the rinse aid?
3)
Why does my dishwasher run so long?
4)
How do I know when the dishwasher is done?
5)
Why do all of the lights stay on?
6)
Why are all of the lights flashing?
7)
Why am I getting a white film on my dishes?
8)
Why is there always water left in the bottom of my
machine?
Refer to your Use and Care Guide for additional information.
Indicates a thermistor fault (heater control). Call your
local service technician.
This simply means the door isn't closed completely.
ANSWERS
ANSWERS
1)
It goes into the compartment between the main detergent
compartment and the rinse aid dispenser. (See page 4.)
2)
The rinse aid goes into the rinse aid dispenser. (See page 5.)
3)
If the temperature of the water entering your dishwasher is below
120°, the dishwasher runs longer because it heats the water to
the proper temperature for the program selected. Raising your
water heater setting may help shorten the cycle times. If this
doesn't resolve the problem, call the ASKO Advisory Center.
4)
See "Understanding the Indicator Lights" on the front of this guide.
5)
See "Understanding the Indicator Lights" on the front of this guide.
6)
See "Understanding the Indicator Lights" on the front of this guide.
7)
You may be using too much detergent or washing your dishes in
water that is too hot. Try using less detergent and use the Normal
or Quick wash programs.
8)
It's normal to have some water left in the sump area near the
drain. If the water fills more than the drain area, see page 9 for
possible solutions.
Refer to this page in
the Use & Care Guide.
3, 4
3
5, 6
4, 5
Art. No. 80 730 99