Asko D1996HNDL 기획 및 디자인 매뉴얼 - 페이지 8

{카테고리_이름} Asko D1996HNDL에 대한 기획 및 디자인 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko D1996HNDL 15 페이지. Standard dishwashers
Asko D1996HNDL에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (12 페이지), 설치 및 사용자 지정 (4 페이지), 기획 및 디자인 매뉴얼 (19 페이지), 사용 및 관리 매뉴얼 (12 페이지)

페이지 인쇄

FITTING THE D1796FI AND D1996FI CUSTOM DOOR PANEL

The D1796FI and D1996FI can only be installed with a fully-

integrated custom door panel that extends from the toe kick to

the counter top. The unit comes with everything needed to make

installing the door panel easy. The door is predrilled for the

panel's mounting screws.

The custom panel should be a minimum of 3/4" (19 mm) thick.

ITEMS PROVIDED WITH THE UNIT

• Two 3/8" screws

• Four 1-3/4" screws

• Four adhesive-backed plastic spacer washers

INSTALLING THE CUSTOM PANEL

Before fitting the custom panel, the dishwasher must be installed

underneath the cabinet. After you've made the required

measurements, pull the machine out again to install the panel.

Refer to the illustration at right for instruction references.

1. Fit the handle (A) onto the panel according to the manufact-

urer's instructions. (NOTE: A handle should be used rather

than a knob, because a knob does not provide enough grip.)

2. Remove the adhesive protection from the washers and place

them in line with the four keyholes (C) on the metal front of

the dishwasher door.

3. Loosen the screws (D) on the outer edges of the dishwasher

door.

4. Pull the turbo fan exhaust frame (E) down until the lower edge

aligns with the lower edge of the cabinets and tighten the

screws. Snap the plastic duct into the turbo fan exhaust vent.

WARNING! The custom panel must not

obstruct the fan exhaust vent; otherwise,

steam from the vent could eventually

damage the cabinet.

5. The two short screws (B) go into the back of the panel, 16-

3/16" (411 mm) from the upper edge of the panel and 5/8"

from the outer edges. Insert the short screws into the panel,

leaving 1/8" (3 mm) of space between the screw head and

the panel.

6. Hook the panel screws (F) into the keyholes (C) on the

dishwasher door.

7. Push the panel upwards until the lower edge aligns with the

lower edge of the cabinets and secure the screws.

WARNING! The custom panel should not extend more

than 2-15/16" (75 mm) below the bottom of the dish-

washer door; otherwise, it will strike the toe kick and

damage the machine and/or the panel.

Specifications are subject to change without notice. See installation instructions for additional details.

ASKO D

CUSTOM PANEL DIMENSIONS

Width:

23-1/2" (597 mm)

Height:

28-1/8"–30-1/8" (714 mm–765 mm)

(Measured from the top of the panel to the lower

edge of the kitchen cabinet.)

Thickness:

Minimum 3/4" (19 mm)

Weight:

Up to 22 lb.

8.Open the door and tighten the screws (F) inside.

ADJUSTING THE DOOR SPRINGS

Before you push the dishwasher into the cabinet opening, test the

door to make sure it stays in place at any angle. If it tends to fall

down, pull out the machine and tension the door

springs on the sides of the machine by moving

them one hole farther back or by twisting the

spring to make it shorter.

ISHWASHER

Shorten