Ambery LCDT6 운영 매뉴얼 - 페이지 15

{카테고리_이름} Ambery LCDT6에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ambery LCDT6 16 페이지. Super video to wxga converter external cable tv tuner

페이지 인쇄

and looking at video channel 2 on TV for video display, you will not see the picture from the

display because of the incorrect video channel being selected by mistake.

Make sure that you do not set the VGA output resolution of this video converter beyond the

maximum capacity that your monitor or projector can handle. Example: If your monitor

display supports up to 1280x1024 pixels but you set this video converter to output at

1920x1200 for output to the monitor, there will be no picture showing in this case and the

monitor will display an error message of "Out Of Frequency Range". At this time please use

the remote control to power off the video converter box first and then press "0" button from

the remote three times continuously. Press the power button again, you shall see the picture

come back up again at 1024x768 pixels resolution. During this process, please do not

unplug the power adapter.

In case of compatibility issue with the VGA display you were using, you can test out this

video converter /TV tuner with a different VGA monitor or projector to find out more

information.

If you can not see TV channels from the tuner of this video converter, please do the channel

scan again as instructed on page 9. Also make sure that you select the right TV system

mode from the OSD menu of this TV tuner unit. Example: If you connect the coax cable

from the wall for CATV into the RF input of this unit, you must select TV system mode as

"CATV" from the OSD menu of this unit as stated on page 10. If you select "AIR TV " mode,

this unit will not work correctly.

If you have digital cable TV service, you must use either a composite rca video cable or

s-video cable to connect from your digital cable box into the composite input or SV input of

this video converter. You can not connect the coax cable from your digital cable box into the

coax input of this CATV tuner. Our unit supports all the SD standard cable TV channels and

it can not decode the digital or HD channels for you. That is why you will be provided with a

digital set top box from your local cable company when you subscribe to digital cable TV

service.

If you have satellite video, you must use either a composite rca video cable or s-video cable

to connect from your satellite receiver's output to the composite input or SV input of this

video converter as illustrated on page 7 in this manual. You can not connect the coax cable

from your satellite receiver to the coax input of this CATV. The coax input of our unit is

designed for cable TV signals only. Any other coax signals will not be decoded properly.

No sound?

Question:

Please check all the audio cable connection first and make sure that you connect cables

correctly between your video device, this video converter and your display unit according to

the diagram shown in this manual.

Please check if your video device outputs audio properly first.

If you have accidentally muted the audio output on your video device or this video converter

or your display end, you will have no audio either. If that were the case, please un-mute the

audio out from your video device, video converter or display accordingly.

Question: No response from the remote controller?

a. Make sure that you are pointing the remote controller of this video converter toward the IR

sensor window of this unit within 20 ft and +/- 15 degrees. The supplied remote control of this

unit uses infrared, not RF type like the ones used from your home TV.

b. Please check the batteries of the remote control and replace with new ones if necessary.

Question: How to reset the unit back to default?

a. User can press the "MENU" button from the remote controller to show the configuration menu

on the screen. Then scroll to "Setup" section and select "Factory mode" to confirm reverting

all the current setting back to the default values as detailed on page 11.