Asko T720 사용 및 관리 매뉴얼 - 페이지 11

{카테고리_이름} Asko T720에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko T720 16 페이지. User manual use & care guide t760-t780 (use & care guide - en, fr)
Asko T720에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 설치 (1 페이지)

페이지 인쇄

CONNECTING

CONNECTING T T O O A A VENTILA

1. Connect the exhaust hose to a ventilation exhaust

fitting or to a discharge through the wall.

2. Secure the hose joint to the outlet stub on the

machine.

3. Run the hose with as few bends as possible to the

point of discharge. If necessary, it can be extended

to a maximum of 22 feet (660 cm) of 4" (10 cm)

diameter ridged pipe.

Make any bends as gentle as possible. A maximum of

four 90° bends may be fitted in the hose. The more

bends and the longer the hose, the less air will circulate

through the machine, which will impede drying

performance. Subtract 4 feet (120 cm) for every 90°

elbow.

Installation Examples

NOTE:

When installing in warm climates (77°F and

above) with high humidity levels, do not

route the air exhaust hose upwards.

FREESTANDING INST

FREEST

ANDING INSTALLA

The dryer can be placed next to the washing machine.

It is essential that the machine is leveled and the

locknuts are tight to eliminate vibration.

There should be at least 1/2" (12.5 mm) of space

between the washer and dryer.

B B UIL

UILT T -IN INST

-IN INSTALLA

ALLATION

MODELS T700/T760

These models can be installed beneath a cabinet or

worktop with a minimum height of 34" (864 mm). There

must be a gap of about 1/4" (.64 mm) all around the

machine, including between the rear edge of the

machine top panel and the back wall. The opening width

must be at least 24" (600 mm).

Space must also be available for the exhaust hose on

the left, right or rear of the machine. See the diagram for

hole sizes and positions. Note that the hole

measurements are to the center of the hole.

MODELS T720/T780

The condensing models work best when they have

good air circulation. Therefore, we don't recommend

that they be installed beneath a cabinet. If it is necessary,

however, be sure to leave a gap of at least 1/2" on all

sides.

VENTILATION DUCT (T700/T760)

TION DUCT (T700/T760)

If more than 22 feet of hose is needed, the diameter

must be increased to 6" or 8" (152 mm or 203 mm).

WARNING!

This appliance should not be exhausted into a

chimney, a wall, a ceiling, or a concealed space of a

building. Only a metal ventilation grill should be used.

If the hose is taken to a wall outlet, a ventilation grill

should be fitted to prevent reverse flow of cold air. Fit the

ventilation grill to the outside or inside of the wall.

Subtract 4 feet

(120 cm) for

every 90° elbow.

If there is only one vent duct from the room, a vent spacer

must be fitted.

ALLATION

TION

NOTE: All hole measurements are

Ventilation grill

NOTE:

Make sure nothing is

blocking the ventilation grill.

Vent spacer

to the center of the holes.

NOTE:

The height adjustment for the dryer is

33-1/2" to 34-1/2" (850 mm to 876 mm).

Do not raise it higher than 34-1/2".

Page 11