Ambient Technologies RCBE 설치 및 운영 지침

{카테고리_이름} Ambient Technologies RCBE에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Ambient Technologies RCBE 2 페이지. Basic on/off remote control – 120vac

페이지 인쇄

RCBE

Basic On/Off Remote Control – 120VAC

INSTALLATION AND OPERATING

INSTRUCTIONS

This basic 120 VAC on/off remote control system provides a safe,

reliable, and user-friendly remote control for millivolt valve gas

appliances. The system can be manually turned on and off with

the transmitter. Always check with the home owner's manual of

the appliance for additional information, warnings regarding

accessory installation before connecting this remote control sys-

tem.

Carefully inspect the contents for shipping damage. If any parts

are missing or damaged, immediately contact the dealer from

whom you purchased the kit. Do not attempt to install any part of

the kit unless all parts are in good condition. Please keep this

booklet for future reference.

CONTENTS OF KIT

Description

Transmitter

Battery Alkaline AAA (for Transmitter)

Receiver (Assembly) consists of :

Receiver Box with 120 VAC Adapter

Slide Button-Black (On/RS/Off)

Wall Cover Plate-Black

Plug-In Wiring Assembly – 22" Inches

Velcro (Loop and Hook)

Installation Instructions

#8 Screw for sheet metal, Black

FEATURES/SPECIFICATIONS

• Battery Powered Transmitter

• Compact 120 VAC Adapter with 30" wire

• Low Battery Indication for Transmitter

• 16 Security Codes

• Quick Disconnect Wiring Assembly

• Optional 6 hour Shutdown Timer on Receiver

WARNING

Important Safety Information

• Read this manual thoroughly prior to installing, programming or

operating any remote control.

• This remote control system is designed for use with a millivolt

gas valve system. Do not use this remote control system on

applications with voltages above 30 Volts AC.

• This remote control system requires three (3) "AAA" batteries

to power the transmitter and 120 VAC to power the receiver.

Wiring must conform to appliance requirement and building

codes/ordinances as required by local and national code authori-

ties having jurisdiction.

• Do not short (or jumper) across the gas valve terminals to test

the remote control installation. This could damage the unit and

void the warranty.

• This remote control system should only be used as described in

this manual. Any other use is not recommended and will void

the warranty.

Turn appliance OFF and allow to cool before

installing or servicing. DO NOT connect

110-120 VAC wiring to the milli-volt gas control

valve. The remote operator must be installed

exactly as outlined in these instructions. Read

all instructions completely before attempting

installation. Follow instructions carefully during

installation. Any modification of components

will void the warranty and may cause a fire haz-

ard.

Turn appliance OFF (at the appliance or remote

receiver) if you are away from your house for a

long period of time.

INSTALLATIONS

Remote Receiver

The remote receiver may be wall mounted or installed in the appli-

ance per the appliance homeowner's manual. Refer to the

Homeowner's Manual for special installation instructions. If wall

mounted, the remote receiver must be installed in a junction box

with cover plate provided. Failure to follow the installation

instructions found in the appropriate Homeowner's Manual will

void the warranty and may cause a fire hazard.

Power up Receiver

Qty

The receiver is powered by plugging into a polarized 120VAC out-

let.

Installing Wire

This system comes with an 22 inch pre-assembled wire assembly.

Insert the white terminal to the back of the receiver. The terminal

wire block can only be installed one way. Do not force the termi-

nal plug onto the receiver.

f i r e - p a r t s . c o m

Follow the homeowner's manual for connecting the two (2) 1/4"

female spade terminals to the millivolt valve.

For applications longer than 22 inches, use 18 gauge wire, 105ºC

rated, with as few splices as possible. Connect to the two (2) 1/4"

female spade wiring terminals. Wire can be no longer than 20

feet.

120VAC Plug for Receiver

Receiver

Make sure that the wires do not contact the

appliances any place other than at the terminals.

Exposure to temperatures higher than 105C

(250ºF) may cause the receiver to malfunction or

fire hazard.

Remote Transmitter

Installing Batteries

The remote transmitter uses three (3) "AAA" batteries. To install

batteries,

1. Press down the battery door tab and lift up and remove the

battery door.

2. Install the batteries as indicated on the transmitter cover.

3. Close the battery door by snap-

ping in place.

4. The batteries should be replaced

at least once every 6 months

or when the battery indicator

flashes.

Setting Privacy (DIP) Switch on

Receiver and Transmitter

The remote receiver and transmitter

privacy (DIP) switches are preset at

the factory. In the event of activation

or interference from other nearby

transmissions, reset the code using the following procedure:

1. Slide the code switches on the transmitter or receiver to your

choice of ON or OFF position. Switches #1, #2, #3 and #4 are

preset to "ON" for both the transmitter and receiver.

2. The switches on the transmitter and receiver must match in

order for the system to work.

3. The system is now ready to operate.

4. See optional 6 hour shutdown on receiver section.

Transmitter

Dip Switch (Default)

Do not use two (2) or more remote control sys-

tems in the same area with the same dip switch

settings, as they will communicate with each

other. This may cause the appliances to mal-

function.

OPERATIONS

Transmitter

mV Valve

General

The RCBE remote control system is an

On/Off remote control.

The transmitter will operate the remote

receiver from 1foot to a maximum of 30

feet. The operational range is reduced

when batteries are low or when the

receiver is inside a metal enclosure.

Initial Start-up

1. After initial power up, the transmitter is ready for use.

Manual Mode

1. Press the ON button once to turn on the appliance. Press

the OFF button to turn it off.

Low Battery Detection

1. When the battery voltage drops to a certain level, the LED

on the transmitter will blink until the battery expires.

Change the battery before the battery is too weak for nor-

mal operation. TURN THE UNIT OFF BEFORE

REPLACING BATTERIES.

Battery

Door

Tab

Back of the Transmitter

Receiver

DIP

OFF