AMD DIrect SSRFR-24S User Manual - Page 6

Browse online or download pdf User Manual for Refrigerator AMD DIrect SSRFR-24S. AMD DIrect SSRFR-24S 9 pages. 15” & 24” refrigerator

Print Page

OPERATING YOUR APPLIANCE

It is recommended that you install the appliance

in a place where the ambient temperature is

between 50°F and 109.4°F (10°C-43°C). If the ambient

temperature is above or below recommended

temperatures, the performance of the unit may

be affected. For example, placing your unit in

extremely cold or hot conditions may cause interior

temperatures to fluctuate. The operating temperature

range may not be reached.

CONTROL PANEL

ON/OFF POWER

To turn the appliance ON or OFF, press and hold the

POWER key

for 5 seconds.

AND DOWN

Press

first, then press

button

SET

to increase (warm) or decrease (cool) the set

temperature by 1°C/ 1°F.

Press

again, the temperature is selected and

SET

shows the actual temperature. If no other further

operation in 6 seconds, display will show actual

temperature in the cooler

°F/°C SELECTOR

Selects the temperature display setting in Fahrenheit

or Celsius degrees. To change the temperature from

Fahrenheit to Celsius or from Celsius to Fahrenheit,

press

and

at the same time, then hold for 6

SET

seconds.

SETTING THE TEMPERATURE CONTROL

The temperature you are setting will increase by

one degree each time you press the

key and

will decrease by one degree each time you press

the

key.

The range of temperature control is from 32°F to 50°F.

To view the set temperature at any time, press

the

key. The set temperature will flash in the

SET

display window for 6 seconds. After 6 seconds, the

temperature inside the until will reappear in the

display window.

(The temperature preset at the factory is 36°F)

15" & 24" REFRIGERATOR USER MANUAL

BEFORE USING YOUR APPLIANCE

Remove the exterior and interior packing.

Before connecting the appliance to the power

source, let it stand upright for approximately 24

hours. This will reduce the possibility of a malfunction

in the cooling system from handling during

transportation.

Clean the interior surface with lukewarm water using

a soft cloth.

Install the handle on the door if not already attached.

INSTALLATION OF YOUR APPLIANCE

Your outdoor refrigerator has been designed for both

built-in and freestanding applications. When built-in,

your refrigerator door does not require additional air

space for top, side or rear. The front grille must not

be obstructed.

NOTE:

It is recommended that you do not install the

appliance near an oven, radiator or other heating

source, as heat sources may increase electrical

consumption. Do not install in a location where the

temperature will fall below 50°F (10°C). For best

performance, do not install the appliance behind

a cabinet door or block the base grille. Plug the

appliance into an exclusive properly grounded wall

outlet.

SITE PREPARATION

1. Position the unit on a flat, level surface capable

of supporting the entire weight of the unit.

Remember the unit will be significantly heavier

once it is fully loaded.

2. Connect the unit to a Ground Fault Interrupter

(GFI).

3. The unit must be installed according to your local

codes and ordinances.

4. ELECTROCUTION HAZARD!

• Electrical Grounding Required - This appliance

is equipped with a 3-prong (grounding)

polarized plug for your protection against

possible shock hazards.

• NEVER remove the round grounding prong

from the plug.

• NEVER use a 2-prong grounding adapter.

• NEVER use an extension cord to connect

power to the unit.

• Where a 2-prong wall receptacle is

encountered or a longer power cord is

required, contact a qualified electrician to

have it replaced in accordance with applicable

electrical codes.

INSTALLATION

LOCATION OF PARTS

1. Position the unit to allow free air flow through the

front grille.

2. Wipe out inside of the unit with a damp cloth.

INSTALLING THE STAINLESS STEEL HANDLE

To install the handle, follow the instructions below.

Remove the right side gasket.

Take out the screws from the bag in the cabinet. Put

the screws in the holes where the handle is to be

installed.

Align the handle with screws, tighten the screws

using a screwdriver until the handle is both flush

and secured tightly against the door side. (DO NOT

overtighten as this may cause damage to the door

surface).

LEVELING THE UNIT

Position the unit on a flat, level surface capable of

supporting the entire weight of the unit when full. The

unit contains four (4) adjustable leveling legs. Turn the

legs clockwise to raise and counterclockwise to lower.

ELECTRICAL CONNECTION

Put the screws on top of the door where the handle is

to be installed. Align the handle with screws, tighten

the screws using the screwdrivers.

WARNING

Improper use of the grounded plug can result

in the risk of electrical shock. If the power

record is cord is damaged, have it replaced by a

qualified or an authorized service dealer.