CO/Tech 36-6826 Instruction Manual
Browse online or download pdf Instruction Manual for Lighting Equipment CO/Tech 36-6826. CO/Tech 36-6826 5 pages. Led downlight
Print PageLED Downlight
Art.no 36-6826
Model D10-023N0-027
Please read the entire instruction manual before using the product and then
save it for future reference. We reserve the right for any errors in text or
images and any necessary changes made to technical data. In the event of
technical problems or other queries, please contact our Customer Services.
Safety
Symbol description
Warning for a possible
hazard which could lead to
serious personal injury and/
or damage to the product if
the stated instructions are
not followed.
Warning for an electrical
shock hazard.
The fitting should not be
covered with any heat
insulating material.
Safety instructions
• This product must only be installed by a qualified electrician.
• Before beginning any electrical installation always disconnect the power
to the circuit you are working on, either by turning off the main circuit
breaker or by removing the fuse from the consumer unit.
• Ensure that there are no electrical wires or water pipes behind the ceiling
panel where you intend to drill the mounting hole.
• The product is intended for flush fitting ceiling installation.
• The product is intended for indoor use only (IP20).
• Min 20 cm distance from the light source to the closest surface.
• Do not touch the light fitting when it is on or before it has cooled
adequately after being shut off.
• Avoid looking directly into the light source when it is on.
• The light source cannot be replaced. The product should be discarded
once it has reached the end of its service life.
• The light source is not dimmable.
Product description
• LED downlight for fixed installation.
• Comes with one white and one silver
accent ring.
• Tiltable lamp body.
GREAT BRITAIN • CUSTOMER SERVICE tel. 020 8247 9300 e-mail [email protected] internet www.clasohlson.co.uk
postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
Installation
Preparations
• This product must only be installed by a qualified
electrician.
• Disconnect the power to the circuit you are working
on, either by turning off the main circuit breaker or by
removing the fuse from the consumer unit.
• Ensure that there are no electrical wires or water
pipes behind the ceiling panel where you intend to
drill the mounting hole.
• Avoid covering the back of the light fitting with any
heat insulating material.
Class II product.
Note:
Double-insulated.
Only intended for
indoor use.
The distance between the ceiling panel and
The product is not
any material present behind it must be at least
dimmable.
50 mm in order for the lamp housing to reach
its full tilting positions.
Connection
1. Cut the incoming mains power wires to a length that allows:
- The lamp to be rotated about 90º in its mounting hole.
- The lamp housing to be tilted to its full extent in all possible directions.
2. Hold the lamp directly under the mounting hole while connecting
the power wires to the terminal block.
Mounting
1. Twist the lamp into its desired position (consider how you want to tilt
the lamp housing to point the light to where you want it).
2. Pull the spring clips back and insert the lamp into the mounting hole.
3. Press the lamp upwards until the accent ring lies flush against
the ceiling panel.
4. Select the desired accent ring colour.
5. If you wish to change the accent ring, turn it anti-
clockwise to remove it.
6. Fit the accent ring's mounting lugs into the lamp
housing's slots and turn clockwise to secure it.
7. Turn on the mains. The light is now ready for use.
Instructions for use
• Do not touch the light fitting when it is on or before it has cooled
adequately after being shut off.
• Tilt the lamp by pushing the edge of glass diffuser to the desired angle.
Care and maintenance
• Turn the lamp off and let it cool.
• Clean the product using a lightly moistened cloth. Use only mild cleaning
Drill a hole into the ceiling
agents, never solvents or corrosive chemicals.
panel with a 68 mm diam
• Make sure that the light fitting is dry before turning it on.
hole saw.
Responsible disposal
This symbol indicates that this product should not be
disposed of with general household waste. This applies
throughout the entire EU. In order to prevent any harm to
the environment or health hazards caused by incorrect waste
disposal, the product must be handed in for recycling so that
the material can be disposed of in a responsible manner.
When recycling your product, take it to your local collection
facility or contact the place of purchase. They will ensure that
the product is disposed of in an environmentally sound manner.
Specifications
Rated voltage
Protection class
LED light bulb
Lumens
Rated life
Outer diam (accent ring) 86.3 mm
Depth
Mounting hole diam
Min mounting depth
Weight
220–240 V AC, 50 Hz
IP20
4 W (not replaceable)
250 lm
15 000 hours
41.4 mm
68 mm
50 mm
75 g