American Standard Williamsburg Elite 2425E-RHO Installation Instructions

Browse online or download pdf Installation Instructions for Bathtubs American Standard Williamsburg Elite 2425E-RHO. American Standard Williamsburg Elite 2425E-RHO 4 pages. 5' whirlpool, integral apron with removable access panel high gloss acrylic shown less all fittings
Also for American Standard Williamsburg Elite 2425E-RHO: Specification Sheet (2 pages)

Print Page

WILLIAMSBURG

ELITE™ 5'

INTEGRAL APRON WITH

REMOVABLE ACCESS PANEL

HIGH GLOSS ACRYLIC

SHOWN LESS ALL FITTINGS

(305mm)

10-1/4

(260mm)

3/4

(19mm)

FINISHED

WALL

SEE FITTING

SPECS FOR

DIMENSIONS

(229 mm)

(813mm)

CUTOUT IN FLOOR FOR DRAIN

C/L OF

SUPPLIES

(76mm)

C/L OF DRAIN

OPTIONAL TO

FINISHED FLOOR

1" WATER

USUALLY BETWEEN

RETENTION

65 & 78

FLANGE

(1651 & 1981mm)

(3 SIDES)

C/L OF

OVERFLOW

3-1/2

(89mm)

TOP OF

DECK

21-1/2

(546mm)

ROUGH

FLOOR

BATH

SUPPORT

MATERIAL

1-1/2 O.D.TAILPIECE

Left-hand version shown

GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL

INSTALLED SIZE

60 x 32 x 21-1/2 (1524 x 813 x 546mm)

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

WHIRLPOOL MIN. OPERATING VOL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

PUMP

General Installation Information

Bath may only be installed in a recess type installation.

Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made

through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as

indicated.

this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position

bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use

drywall screws w/washers or roofing nails immediately above the flange of the tub.To secure the tub to steel studs use 4" drywall screws and

flatwashers.

See page 2 for complete installation information.

Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against

the bottom of the tub apron, also holding the tub in place.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

752876-100 Rev. E

2425E-LHO

2425E-RHO WHIRLPOOL

INSTALLATION INSTRUCTIONS

(1524mm)

WATER

RETENTION

FLANGE

(8) JETS

(3 SIDES)

(406mm)

PUMP

ACCESS TO PUMP/MOTOR

(2) AIR VALVES

THROUGH REMOVABLE

FRONT ACCESS PANEL

C/L OF

SHOWER ARM

FINISHED

WALL

IN-LINE HEATER

REMOVABLE

C/L OF

BLANK

VALVES

C/L OF

SPOUT

(305mm)

OPT.

TILING

LEVELING STRINGER

(102 mm)

FLANGE

NOT FOR SUPPORT

UNDERSIDE

OF DECK

21-1/4

(540mm)

REF.

DIM

1-1/2 N.P.T.M.

THREADS

2-3/4

(70mm)

4-5/8

(117mm)

115 Lbs. (52 Kg.)

574 Lbs. (258 Kg.)

55 Gal. (208 L.)

45 Gal. (171 L.)

16-1/4 x 38-1/4 (413 x 972mm)

26-1/4 x 52-1/2 (667 x 1334mm)

15 (381mm)

43 Lbs./Sq.Ft. (208 Kgs./Sq.m)

20.8

35.3

1.6 HP, 9.7 AMPS,120V.

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to

you after careful inspection. the whirlpool version is completely

assembled with pump, motor, and system piping. All you need to finish

the installation are your selected fittings and electrical connections for

a whirlpool. To insure maximum performance and pleasure from this

product, please follow the instructions and cautions.

List of Optional Components (not included):

• Flex-Jet Pulse Jet Kit*

ON/OFF

SWITCH

• Flex-Jet Soft Jet Kit*

• E-Z-Install Heater*

List of Required Components (not included):

• Drain*

* see your Home Depot Retailer

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard

Woodworking Tools

• Personal Safety

Equipment

• Caulking Gun

General Installation Information

Carefully uncrate and inspect your new bath for any shipping damage.

If such damage is found, report it to your vendor immediately. After

inspection and during installation, protect the bath from construction

damage. Before installation, and before enclosing with wallboard,

tile, etc., water test the unit and check for leaks. Do not make

modifications to the whirlpool system or remove pump from factory

mounting. This could adversely affect the safety and performance of

the whirlpool and void the warranty. Do not handle or move the

whirlpool by the pump, motor, or piping system. Fittings (bath filler,

shower arm, etc.) are not provided with the bath and must be ordered

separately. Framing and enclosing materials are provided by others.

IMPORTANT: Water test unit before installation and

enclosure!

• Bath Filler*

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 3 or 2 x 2

Stringers

• Drop Cloth

• 15 amp GFI

Outlet

• Cement, Plaster,

Grout

All product names listed herein are trademarks

of American Standard Inc. unless otherwise noted.