Da-Lite DESIGNER DA-TAB ELECTROL Instruction Book - Page 2

Browse online or download pdf Instruction Book for Projector Accessories Da-Lite DESIGNER DA-TAB ELECTROL. Da-Lite DESIGNER DA-TAB ELECTROL 6 pages.

Print Page

PRE-INSTALLATION

Before proceeding with the installation of the screen, please read the installation and operations instructions thoroughly!

▲

CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by

hand.

1. Carefully unpack the screen and remove the outer wrapping.

2. Always handle screen in upright position.

3. Remove the front cover of the screen from the back of the screen. Lift front cover up

approximately 1/2" and pull away from back of screen. See Figure 1.

4. Remove hex head screws that secure the metal shipping brackets to the wood board.

5. Remove the Phillips head screws that attach the screen case to the wood board.

6. Remove the metal shipping brackets from the back of the slat.

7. There are two methods of mounting the screen,

suspended from ceiling and wall mounted. See Figure 2.

NOTE: Allow 1/2" above screen (when mounted) for front

cover of screen installation and removal.

8. Picture surface is centered in case. Case extends 7"

beyond surface on either end. Do not attach anything to

screen slat on the bottom of the screen.

INSTALLATION

1. Hang screen from wall or ceiling.

FOR WALL MOUNTING

HARDWARE PROVIDED

2 – "V" Bars ( one is factory mounted to the back of the case; one will be mounted to the wall)

6 – Toggle Bolts, 4"

6 – Lead Shields, #10-14 x 1

6 – Phillips Flat Head Wood Screws, #10 x 2"

TOOLS REQUIRED

Electric Drill

Masonry Bit

" (if mounting in solid masonry or concrete)

Screw Driver, #2 Flat Tip (if using toggle bolts) or #2 Phillips (if mounting in solid masonry or concrete)

Determine the height of the top of the case from the floor. This will be the height of the wall mounted "V" bar.

Hold the loose "V" bar to the wall at the height determined above (MAKE SURE IT IS LEVEL), and mark the loca-

tion for the screw holes. To mount the "V" bar on solid concrete or masonry wall, drill

lead shields. Fasten the "V" bar to the wall using the #10 x 2" wood screws. If you are mounting to a hollow

wall, drill

" holes and insert the toggle bolts. Then fasten the "V" bar to the wall with the toggle bolts. Now set

the case in place on the wall with the "V" bar of the case nestled into the "V" bar on the wall.

FOR CEILING MOUNTING

Position and properly anchor screw hooks into ceiling, beam or other solid surface. Then proceed to use the two

"D" rings that are factory mounted to the top of the case to hang the case securely.

2. Install electrical hook-up that applies to your unit. Make sure to review your electrical installation checklist and wiring

diagrams (included) for either 120 volt switch, 220/240 volt switch or low voltage control. See Figure 3.

3. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1

MIN. ON / 3 MIN. OFF.

NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

WALL MOUNTING

CEILING

ALLOW A MINIMUM OF

1-1/4" FROM CEILING

"V" BAR MOUNTED

TO THE WALL

WALL

"V" BAR

PICTURE

MOUNTED TO

SURFACE

THE BACK OF

THE CASE AT

THE FACTORY

FIGURE 2

HANGER BRACKET

HANGER

BACK OF

SCREEN

FRONT

COVER

PICTURE SURFACE

SLAT

FIGURE 1

CEILING MOUNTING

PLACE "D"

RINGS OVER

HOOKS WELL

SECURED IN

CEILING.

PICTURE

SURFACE

" holes and insert the