AmerTac TM08DHBL Instruction Manual

Browse online or download pdf Instruction Manual for Timer AmerTac TM08DHBL. AmerTac TM08DHBL 2 pages. Programmable power strip timer

Print Page

http://waterheatertimer.org/GE-timers-and-manuals.html

Programmable

Power Strip Timer

Instruction Manual & Warranty

Getting Started

Make sure the lamps/appliances are working, by plugging them

into the wall outlet and turning them on.

While they are on, remove the plug from the wall outlet.

The cover protects the timer 'face' from dirt and dust, and it

'hides' the operating controls when not in use. You will need

to open the cover when programming the time and settings,

and then you can close the cover after programming has been

completed.

There are 96 non-removable pegs on the front of the timer.

These pegs can be pushed up (away from the middle area) or

pushed down towards the middle area). Make sure that all of the

pegs are pushed DOWN.

There is a knob in the middle area, which can be turned

clockwise or counterclockwise, so that the arrow aligns with

either the – (ON), the

(AUTO), or the

Make sure the arrow aligns with the

There is a red OFF/RESET button near the base of the cord.

Make sure the button is set to RESET.

Holding the pegs, rotate the dial clockwise through at least one

complete revolution.

Programming the On/Off Times

Turn the middle knob so that the arrow aligns with the

(OFF) icon.

Locate the time(s) at which you wish the lamps/appliances

to turn ON and OFF, paying attention to the AM or PM

designation.

Each peg represents 15 minutes. Push the pegs UP during

the time periods when you would like the lamps/appliances

to be turned ON.

Push the pegs DOWN during the time periods when you

would like the lamps/appliances to be turned OFF.

Setting the Current Time

You must set the current time, in order for the timer to turn

ON and OFF correctly at the programmed times.

Holding the pegs, rotate the dial clockwise until the current

time aligns with the arrow, paying attention to the AM or

PM designation.

Installation/Use

There are 8 outlets on the power strip. Four of the outlets are

surrounded by a border and the

plugged into any/all of these 4 outlets will be controlled by the

timer. Lights/appliances plugged into any/all of the other 4 outlets

will NOT be controlled by the timer.

Plug the lights/appliances into any of the

power strip. Plug the timer power cord into the wall outlet.

Make sure the lamps/appliances are set to ON.

Turn the middle knob so that the arrow aligns with the

(AUTO) icon. The timer will now automatically turn ON

and OFF at the programmed times.

AmerTac

™

Saddle River Executive Centre

One Route 17 South

Saddle River, NJ 07458

www.amertac.com

Made in China/Hecho en China/Fabriqu en Chine

Manual Override Function

You can override the programmed setting temporarily (i.e. turn

the lamps/appliances ON when the timer is set to OFF or turn

the lamps/appliances OFF when the timer is set to ON.)

(OFF) icons.

(AUTO) icon.

Master Switch/Circuit Breaker

You can turn off power to ALL of the lights/appliances which are

plugged into the power strip. In addition, when the unit is overloaded

(when the combined wattage of the lamps/appliances exceed the

capacity of the timer), the power will automatically turn off.

NOTE: This power strip is not a surge protector.

WARNING:

CAUTION: To Reduce the Risk of Electric Shock,

Use Only Indoors

CAUTION: Use Only in Dry Locations

In case of power failure, reset timer.

Combined wattage of lamps/appliances must not exceed capacity

of timer.

Do not use the timer with heaters or similar appliances.

Always ensure the plugs of the lamps/appliances are fully inserted

into the timer outlet.

To clean the timer, remove from the wall outlet and wire with

a dry cloth.

Do not immerse the timer in water or any other liquid.

Specifications:

120V~, AC

(AUTO) icon. Lights/appliances

15A, 1875 Resistive

Minimum ON/OFF Switching Interval: 15 minutes

outlets on the

Limited One Year Warranty

AmerTac

workmanship for a period of one year from the date of purchase. AmerTac's

obligations are limited to repairing or replacing any defective unit and are

effective only if such units are returned within one year of the purchase date

to AmerTac, Saddle River Executive Centre, One Route 17 South, Saddle River,

NJ 07458. Warranty void if damage is due to misuse or improper installation.

In no circumstance will AmerTac

damages relating in any way to this product.

Temporizador con Tira de Alimentación Programable

Minuteur pour barre d'alimentation programmable

When the lamps/appliances are OFF at the programmed

time, turn the middle knob so that the arrow aligns with

–

the

(ON) icon. The lamps/appliances will turn ON.

When the lamps.appliances are ON at the programmed

time, turn the middle knob so that the arrow aligns with

the

(OFF) icon. The lamp or appliance will turn OFF.

In order for the timer to automatically turn ON or OFF at the

programmed times, turn the middle knob so that the arrow

aligns with the

(AUTO) icon.

Press the OFF/RESET button (near the base of the cord) to OFF.

The light on this button will turn OFF.

To turn ON the lights or appliances again, press the OFF/RESET

button to RESET, and the light on this button will turn ON.

™

warrants this product to be free from defects in material and

™

be liable for consequential or incidental

Questions?

800-777-0802

TM08DHBL

I04-0040-A