Dooya DM25LEU/S-1.1/28 Instructions

Browse online or download pdf Instructions for Indoor Furnishing Dooya DM25LEU/S-1.1/28. Dooya DM25LEU/S-1.1/28 2 pages.

Print Page

SAFETY NOTE

1. This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe

way and understand the hazards involved.

2. Children shall not play with the appliance.

3. Cleaning and user maintenance shall not be made by

children without supervision.

4. If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

5. WARNING: the drive shall be disconnected from its

power source during cleaning, maintenance and when

replacing parts.

6. The instructions shall state that the A-weighted emis

sion sound pressure level of the drive is equal to or

less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).

7. The mass and the dimension of the driven part shall be

compatible with the rated torque and rated operating

time.

8. The type of driven part the drive is intended for.

9. WARNING: Important safety instructions. It is important

for the safety of persons to follow these instructions.

Save these instructions.

10. Do not allow children to play with fixed controls. Keep

remote controls away from children.

11. Frequently examine the installation for imbalance and

signs of wear or damage to cables and springs. Do not

use if repair or adjustment is necessary.

12. Watch the moving shutter and keep people away until

the shutter is completely closed.

13. WARNING: Important safety instructions. Follow all

instructions, since incorrect installation can lead to

severe injury.

14. Before installing the drive, remove any unnecessary

cords and disable any equipment not needed for

powered operation.

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

DM25LEU/S

Instruction

A-04

Features

Built-in Receiver

Switch Direction

Jog & Tilt

Stall Protection

Built-in Lithium Battery

Program Button

Scan and Program

Reset to Factory Mode

Status Feedback

Memorized Setting

Fields of Application

The motor is suitable for motorization of roller blinds.

Specifications

Working temperature: -10℃ ~ +50℃

Radio Frequency: 433.925MHz

Input Voltage: USB 5V 1A / USB 5V 2A

Maximum Running Time: 6 minutes

Following data for reference

Rated Torque

Rated Speed

Model

(N.m)

(rpm)

DM25LEU/S-0.7/28

0.7

DM25LEU/S-0.7/34

0.7

DM25LEU/S-1.1/28

1.1

DM25LEU/S-1.1/40

1.1

* For reference only.

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.

Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer's liability and warranty.

-1-

Charging Instructions

Micro-USB Port

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and

needs to be charged.

During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped

Electronic Limit

running and needed to be recharged.

Preferred Stop Position

Speed Regulation

Scene Control

Rechargeable Battery

Blinking red:

Low battery alert

Motor Installation

Drive tube

Step 1 Cut drive tube to required length.

Rated Power

(W)

①Crown

②Drive Adapter

③Circlip

Step 3 Mount correct crown & drive adapter on

the motor. Make sure drive adapter fits firmly and

crown rotates freely.

Caution

1. Do not expose motor to humid, damp or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna and keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If power cable or connector is damaged, do not use.

6. Ensure correct crown and drive adaptor are used.

7. Ensure power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls shall be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

11. Installation and programming to be performed by a qualified professional, use or modification outside

the scope of this instruction may void warranty.

Micro-USB charging: 5V

Blinking green:

Solid green:

Charging is processing

Battery has

finished charging.

Drive tube

Step 2 Ensure tube edge is clean and burr-free.

Bracket

Step 4 Align the notches on the crown and drive

adapter with the drive tube, slide and fit the motor

into drive tube. Mount idler and bracket on both

ends.

-2-