Astria Fireplaces H9021 Installation Instructions - Page 2
Browse online or download pdf Installation Instructions for Fireplace Accessories Astria Fireplaces H9021. Astria Fireplaces H9021 2 pages. Glass media kit
INNOVATIVE HEARTH PRODUCTS • SIGNATURE SERIES DIRECT-VENT GAS FIREPLACES • ENVY/ENVY CD 35/40/45TEN • INSTALLATION INSTRUCTIONS
8. Carefully grip the door at the top and bottom, and remove it
from the fireplace. Place the door in a secure location where
it will not be damaged.
Figure 1: Removing the surround trim assembly
Figure 2: Upper And Lower Glass Door Latches
SCALE 0.200
f i r e - p a r t s . c o m
Hot Fireplace Will Cause
• Any attempt to use media not specified for your
fireplace configuration will result in incomplete
Severe Burns
combustion, sooting, and poor flame quality, and
will void the warranty.
Never Allow Children to
• HANDLE MEDIA ONLY WHEN COOL. Turn OFF
Touch Glass or other Fire-
all electricity to the appliance before removing
place Parts
or installing media. Media gets very HOT during
fireplace use and will remain hot up to ONE HOUR
after the gas supply is turned off.
• If media is not installed according to the installation
instructions, fl ame impingement and improper
combustion could occur, resulting in soot and/or
excessive production of carbon monoxide (CO), a
TOXIC gas that is colorless and odorless.
Innovative Hearth Products reserves the right
to make changes at any time, without notice,
in design, materials, specifications, prices and
also to discontinue colors, styles, and products.
Consult your local distributor for fireplace
code information Printed in U.S.A. © 2014
Innovative Hearth Products, LLC .
P/N 900005-06 Rev. NC 10/2014
Side Tabs
Latch
Latch
Latch
WARNING
WARNING
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installing the Glass Media
1. Complete the steps in Accessing the Firebox.
2. Install the glass media in the recessed area between the
front and rear floors. Spread the glass media evenly over
the designated area.
NOTE: DO NOT mound the glass media. Place a thin layer
of glass media over the burner and pilot areas (Figure 3).
NOTE: 35 in. fireplaces require less than a full bag of
glass media. 40 in. fireplaces require an entire bag. 45 in.
fireplaces require an entire bag, and may use a portion of
another bag (purchased seperately).
Figure 3: Glass Media Installed
Pilot Area
3. Complete the steps in Closing the Firebox.
Removing the Glass Media
1. Complete the steps in Accessing the Firebox.
2. Use a clean, dry, empty shop vac to remove the glass media
from the fireplace.
3. Complete the steps in Closing the Firebox.
Cleaning the Glass Media
1. Place the glass media in a colander or sieve, and carefully
rinse under hot water.
2. Spread the glass media in a thin layer on a flat surface to dry.
3. Allow the glass media to completely air dry before reinstalling.
Closing the Firebox
1. Carefully position the glass door in front of the firebox and
hook the two upper spring-loaded latches over the glass door.
Then, hook the two lower spring-loaded latches over the
glass door.
2. Use an ammonia-free glass cleaner and a soft, non-abrasive
cloth to remove fingerprints and smudges from the glass door.
3. Align the surround trim assembly with the mounting slots
along the left and right edges of the firebox and press in and
down to lower it into position. Reinstall the left and right
side finish trim gap fillers.
4. Use an ammonia-free glass cleaner and a soft, non-abrasive
cloth to remove fingerprints and smudges from the
surround trim assembly.
5. Apply electrical power and turn ON the gas supply for
the fireplace.
P900005-06
Burner Area
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.US.com