Flying Industry Development 4S1PFC-AC220+CV-8-3 Quick Manual - Page 2

Browse online or download pdf Quick Manual for Remote Control Flying Industry Development 4S1PFC-AC220+CV-8-3. Flying Industry Development 4S1PFC-AC220+CV-8-3 3 pages. Rf wireless remote control kit

Print Page
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button ▲ of first row : motor of receiver 1 rotates in positive direction.
Press button ▼ of first row : motor of receiver 1 rotates in reversal direction.
...
Press button ▲ of fourth row : motor of receiver 4 rotates in positive direction;
motor of other recei v er stops.
Press button ▼ of fourth row : motor of receiver 4 rotates in reversal direction.
Setting control mode Momentary: Only connect Jumper-1 (CN1)
Press and hold button ▲ of first row: motor of receiver 1 rotates in positive direction. Release button ▲ of fi r st row : Motor stops.
Press and hold button▼ of first row: motor of receiver 1 rotates in reversal direction. Release button ▼ of first row : Motor stops.
...
Press and hold button ▲ of fourth row : motor of receiver 4 rotates in positive direction. Release button ▲ of fourth row: Motor stops.
Press and hold button▼ of fourth row: motor of receiver 4 rotates in reversal direction. Release button ▼ of fourth row: Motor stops.
Lim it control term inals:
Limit control terminals S1 and S2 are normally open, you can connect limit sw itches or sensors (normally open type) to terminals S1 and S2, and
then you can use limit sw itches or sensors to stop the motor.
When motor rotates in positive direction, if connect two terminals of S1, the motor w ill stop automatically.
When motor rotates reversal direction, i f connect two terminals of S2, the motor will stop automatically.
Wired control term inals:
You can connect manual sw itches, external devices or sensors (w ith low level output signal) to control the motor.
1) The manual sw itches:
You can connect manual sw itches to terminals "Signal 1+", "Signal 1-", "Signal 2+", "Signal 2-", then you can use manual switches to control the
motor.
When connect terminals "Signal 1+" and "Signal 1-", motor rotates in positive direction. And when di s connect "Signal 1+" and "Signal 1-", motor stops.
When connect terminals "Signal 2+" and "Signal 2-", motor rotates in reversal direction. And when disconnect "Signal 2+" and "Signal 2-", motor
stops.
2) Signal input:
You can connect external devices (with low level output signal) to terminals "Signal 1+", "Signal 1-", "Signal 2+", "Signal 2-", then the external
device' s output signal can control the motor.
When the external devi c e outputs low level signal to terminal "Signal 1-" and "Signal 1+", motor rotates in positive direction.
When the external devi c e outputs low level signal to terminal "Signal 2-" and "Signal 2+", motor rotates in reversal direction.
How to pair the transm itter to the receiver:
1) Press the learning button of recei v er for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process w ill be discontinued.
4) The receiver can learn several remote control s with di f ferent codes.
Delete all transmitters:
We have learned remote control to the recei v er. If you don't want the receiver to work with the remote control, you can delete all codes of remote
control s , which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slow l y ; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com