Flying Mole PA–S1 Owner's Manual - Page 2

Browse online or download pdf Owner's Manual for Amplifier Flying Mole PA–S1. Flying Mole PA–S1 2 pages.

Print Page

Connections

■ Connecting Devices

●

Make sure the power of all related equipments is turned off, when wiring and checking their polarity.

●

Make sure that the cable is not shorted, when connecting the speaker cable.

●

Connect the power cable after all connections are complete.

●

This product should be placed close to the main source of electrical power (wall outlet in your house)

and keep the power plug within reach.

●

Connectors names may be different from this manual.

✱ Refer to the owner's manuals of the equipments to be connected as well.

Connection Example 1: Common setting for playing stereo sounds

CD Player, etc.

Memory Player, etc.

LINE OUT

Stereo LINE OUT

Jacks

Jack

Speaker

LINE IN Jacks

Power Amplifier (2 channel)

Specifications

Total Harmonic Distortion

0.01% (5Hz – 100kHz)

Frequency Response

DC – 20kHz (+0dB / –0.2dB)

S/N Ratio

100dB (IHF-A)

Input Sensitivity / Input Impedance

150mV / 10kΩ

Output Level / Output Impedance

1V / 1kΩ

Power Consumption

7W (AC 120V model) , 8W (AC 230V model)

Power Supply

AC 120V 60Hz (U.S.A. & Canadian model) / AC 230V 50Hz

Use Environment

0°C – 40°C

Max. Dimensions inch / mm

11–1/16"(W) x 2–3/8"(H) x 10–7/8"(D) mm / 281(W) x 60(H) x 277(D) mm

Weight

3.8 kg (8.4 lbs)

* Nameplate is on the bottom of the product.

* Due to product improvement, specifications and/or product design are subject to change without notice.

Dimensions

281 (11-1/16")

HDD Recorder, etc.

LINE OUT

LINE IN Jacks

Jacks

(for recording analog sounds)

Connect to AC Outlet

AC Power Cable

(*1) XLR cables can be used if the power

amplifier to be connected has BAL-

ANCE INPUT jacks.

(*1)

The signal arrangement of the BAL-

ANCE OUTPUTS on this products is:

1: GND,

2: HOT, and

3: COLD

BALANCE IN Jacks

Unit: mm (")

● Connection of the REMOTE POWER CONTROL Trigger

By connecting the REMOTE POWER CONTROL Trigger, the activation/deactivation of power on a Flying

Mole power amplifier equipped with REMOTE POWER CONTROL Trigger Input can be interlocked with the

activation/deactivation of power on this device. Refer to the owner's manuals of the devices to be connected

as well before connecting cables.

1. Remove the attachment to the REMOTE POWER CONTROL connectors.

2. Remove insulation material around the ends of the supplied remote con-

nection cables and twist the wires until they are stranded securely.

3. Insert the wires into the holes in the attachment and tighten the screws

to fix the cables.

* Treat the other ends of the cables (power amplifier side) as in the steps 1 to

3 above. (Remove the connectors attached to the power amplifier.)

4. Plug the attachement back to the REMOTE POWER CONTROL con-

nector and connect the other end to the power amplifiers.

* Commercially available vinyl insulated cables can be used as well.

• Compatible cable type is AWG24 to AWG12.

Refer to the steps 1 through 4 above when connecting cables and make

sure that the polarity is correct.

* Refer to the "Connection Example 1" for connection to INPUT jacks and AC IN jacks.

Speaker

Maintenance

Never use liquids such as benzine, thinners,

etc., chemically treated cloths, and do not spray

any aerosol type insecticides on the amplifier.

Clean the case using only a soft, dry cloth.

If the amplifier becomes soiled, mix a solution

of water and a neutral detergent then dampen

a soft cloth in the solution, wring out as much

of the solution as possible, and clean the am-

plifier. Then use a soft, dry cloth to wipe the

surface dry.

Questionnaire

There is a questionnaire in the "Support" section in our website.

This is for helping us serve you better by developing new products.

We look forward to your access to the following URL.

Security of Collected Information

We maintains strict physical, electronic, and administrative safeguards to protect

your personal information from unauthorized or inappropriate access. We

restricts access to information about you to who need to know the information to

respond to your inquiry or request. Who misuse personal information are subject

to disciplinary action.

This document is printed with soy ink

(an organic ink made from soy oil) on

recycled paper. Environmentally

friendly printed matter.

(Be sure to check polarity before connection)

Connection Example 2: Bi-amp connection

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

LINE IN Jack

Power Amplifier

(1 channel)

Pin Jack Cable

http://www.flyingmole.co.jp

Supplied remote

connection cable

–

* Be sure to check polarity before

connection.

Connect the black cable to the

negative terminal.

Speaker (L)

Tweeter

HIGH

Midrange

MID

LOW

Woofer

Speaker (R)

Tweeter

HIGH

Midrange

MID

LOW

Woofer

Liquids

Benzine

Soft cloth

Neutral

detergent

FLYING MOLE CORPORATION

5199-1 Waji-cho, Hamamatsu 431-1115 Japan.

Tel : +81-53-486-6030 Fax : +81-53-486-6033

http://www.flyingmole.co.jp [email protected]

FP40781-000