Canyon 98-161 Assembly Instructions Manual - Page 14
Browse online or download pdf Assembly Instructions Manual for Indoor Furnishing Canyon 98-161. Canyon 98-161 14 pages. Cottage colors collection bunk bed
Print Page
1.- ASSEMBLE BED, USING ONE HEADBOARD (M), ONE FOOTBOARD (N) AND TWO SIDE RAILS (E).
2.- INSERT TWO CROSS DOWELS (H) IN ACCESS HOLE INSIDE THE SIDE RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9
3.- ATTACH TWO SIDE RAILS (E), TO HEADBOARD (M)&FOOTBOARD (N), INSERTING TWO 80MM FLAT HEAD BOLTS (G) INTO TO HEADBOARD &FOOTBOARD HOLES, USE THE 5MM ALLEN WTENCH (I) TO TIGHTEN BOTH
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),
FLAT HEAD BOLTS
4.- PLACE 4 SLATS (O) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH HEADBOARD&FOOTBOARD ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG. A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE
FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (P), SEE FIG.12
5.- PLACE IT UNDER THE STEP BUNK BED, AS SHOWN IN FIG.13
6.- ALIGN THE PRE-DRILLED HOLES IN LONG PART OF METAL HOOKS BRACKETS (K) WITH THE PRE-DRILLED HOLES IN THE LADDER (J),THEN SECURE WITH 1" SCREWS (L) USING PHILLIPS HEADSCREWDRIVER (NOT
,
INCLUDED )
SEE FIG. B, AND HOOK THE LADDER IN THE PROPER POSITION, ADJUST AND ALIGN THE PRE - DRILLED HOLES IN THE SHORT PART OF METAL HOOKS ON TOP SIDE RAIL, THEN SECURE THE LADDER,
AS SHOWN IN FIG.13
FIG.12
1.- FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
2.- ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
3.- SURFACE OF MATTRESS MUST BE AT LEAST 5 IN BELOW THE UPPER EDGE OF GUARDRAILS.
4.- DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
5.- PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
6.- PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL CONNECTORS ARE TIGHT.
7.- DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED.
8.- ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
9.- DO NOT USE SUBSTITUTE PARTS. CONTACT THE MANUFACTURER OR DEALER FOR REPLACEMENT PARTS.
10.- USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD USING THE UPPER BUNK.
11.- IF THE BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT, ENTRAPMENT BETWEEN
THE BED AND THE WALL.
12.- ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK.
13.- THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
STRANGULATION HAZARD .
14.-
LIMITED TO HOOKS, BELTS AND JUMP ROPES.
15.- KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THE UPPER AND LOWER BUNK BED IS DESIGNED TO USE ONLY MATTRESS WHICH IS
THE UPPER AND LOWER BUNK BED IS DESIGNED TO USE ONLY MATTRESS WHICH IS
37 1/2"
THE BUNKIE BOARD IS REQUIRED TO
NOTE:
ENSURE THICKNESS OF MATTRESS AND FOUNDATION COMBINED DOES NOT EXCEED
REPLACEMENT PARTS, INCLUDING ADDITIONAL GUARDRAILS, MAY BE OBTAINED FROM ANY OF OUR CANYON
REV 01 08/08/16
CANYON FURNITURE COMPANY.
TWIN/FULL BED ASSEMBLY
FIG. 13
SAFETY WARNINGS
NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED, FOR EXAMPLE, BUT NOT
SIZE OF MATTRESS AND FOUNDATION
74"
74"
74"
TWIN BED
WIDE X
LONG FOR
AND
98-705 TOP BUNK BED END (2 PCS)
98-208 6 DRAWER DRESSER
98-602 3 DRAWRE COMPUTER DESK
98-730 6 PCS SIDE RAILS
98-720 LADDER
98-707 TWIN BED
98-645 4 PCS SLAT PACK 3/3 (2 PCS)
WARNING:
THE BED SLATS WILL NO SUPPORT A
MATTRESS ALONE,A SLAT PACK OR A
BUNKIE BOARD IS REQUIRED FOR
PROPER SAFETY.
( NOT INCLUDED )
REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.12
( USE ONE 4 PCS SLAT PACK FOR 98-707 (98-645) )
FIG.B
75"
37 1/2"
38 1/2"
TO
LONG AND
TO
75"
57 1/2"
58 1/2"
TO
LONG AND
TO
57 1/2"
X 74"
FULL BED.
WIDE
LONG FOR
8 1/2"
AND MATTRESS IS AT LEAST
98-705 TOP BUNK BED END (2 PCS)
98-208 6 DRAWER DRESSER
98-602 3 DRAWRE COMPUTER DESK
98-730 6 PCS SIDE RAILS
98-720 LADDER
98-709 FULL BED
98-645 4 PCS SLAT PACK 3/3
98-646 4 PCS SLAT PACK 4/6
FURNITURE COMPANY DEALERS
PAGE 2 OF 2
( USE ONE 4PCS SLAT PACK FOR 98-709 (98-646) )
AND
TIPS # 1
TWIN BED
.
WIDE FOR
FULL BED.
WIDE FOR
5"
BELOW UPPER EDGE OF GUARDRAILS.
FIG.C
TIPS # 2
KIS01131