Dover DESTACO ROBOHAND DRG Series Manual - Page 2
Browse online or download pdf Manual for Controller Dover DESTACO ROBOHAND DRG Series. Dover DESTACO ROBOHAND DRG Series 4 pages.
Print Page
3.1-3.45 (RR_DRM) RED.qxd
DRG Series
DRG SERIES EXPLODED VIEW
Rotary Actuators | Maintenance and Assembly Procedure
18
3.44
6
19
15
-R Option Shown
Rotational Adjusters
Assembly Procedure
1) Press the Upper Bearing #4 onto the Pinion #2.
2) Install the Retaining Ring#9 or Hex Nut #10 onto the Pinion #2.
3) Assemble the Rack #6 to the Piston #7 with Roll Pins #19.
4) Grease the U-Cups #13 and install them onto the Piston #7.
5) Press the Magnet #14 into the Piston #7.
6) Assemble the Bumper #12, Washers #15 and Bumper Screw #16
onto the Piston #7.
7) Lubricate the Body #1 bore and install the Piston Assembly into
the body.
8) Press the Lower Bearing #5 into the Body #1.
9) Locate the Piston assembly so it is aligned with an outer edge
of the body.
10) Lubricate the Pinion assembly and align the key with the same edge
of the Body as the Piston and Press the Pinion into the Body.
Seal Kit
Items
For more information call us at: 1-800-ROBOHAND or 203-261-5558 Fax: 203-452-7418 Visit us on the Internet at: www.destaco.com
2/7/06
1:12 PM
Page 44
17
3
11
12
13
7
14
16
20
5
21
22
23
24
25
Thread
Krytox
™
Locker
Lubricant
120
ITEM #10 IS
FOR -094,-106
AND -131 ONLY
8
10
9
4
4
2
2
1
11) Rotate the Pinion through the full travel and insure that the
Piston is correctly located in the Body, adjust the travel of the
Piston if necessary.
12) Grease the Gasket and install the End Plate #3 onto the Body #1.
13) Install the 2 Orifice #20 into the Body #1 screw them in until they
bottom.
14) Install the Bearing Flange #8 with the 4 Flange Screws #17.
-R Option Assembly Procedure:
1) Screw the Angle Adjuster into the End Block Angle Adjuster.
2) Place the sealing washer over the threaded extension.
3) Screw on the Hex Nut over the Sealing Washer.
4) Screw the End Block onto the Body with a Gasket.
Lightweight
Teflon
Based
™
Machine Oil
Grease
Dimensions and technical information are subject to change without notice
Item Qty
Name
01
1
Body
02
1
Pinion Shaft
03
2
End Plate
04
1
Upper Bearing
05
1
Lower Bearing
06
1
Rack
07
1
Piston
08*
1
Bearing Retainer
09*
1
Retaining Ring
10
1
Hex Nut
11
2
Gasket
12
2
Bumper
13
2
U-cup
14
1
Magnet
15
2
Bumper Washer
16
2
Bumper Screw
17
4
Retainer Screw
18
8
End Plate Screw
19
2
Roll Pin
20*
2
Fixed Orifice
21
2
Angle Adjuster
22
2
End Plate Rotational
Adjuster
23
2
Seal Washer
24
2
Hex Nut
25
8
End Plate Rotational
Adj. Screw
*NOTES:
1) Contact the Robohand Sales
Department for a complete spare parts
list with order numbers and prices.
2) Item #09 is for size -075 only.
3) Item #10 is for size -094, -106
and -131 respectively.
4) Item #20 not in size -131
Super
Third Angle
Bonder
Projection