Amprobe AM-45 User Manual - Page 3

Browse online or download pdf User Manual for Test Equipment Amprobe AM-45. Amprobe AM-45 9 pages.

Print Page

-Electric Field EF-Detection (AM-47 & AM-45 only)

From AutoCheck

with "Auto" being displayed, press the SELECT button momentarily 2 times to select EF-

Detection feature. The meter displays "EF" when it is ready. Signal strength is indicated as a series of bar-graph

segments on the display and variable beep tones.

●Non-Contact EF-Detection: An antenna is located at the top left corner of the meter, which detects electric field

surrounds current-carrying conductors. It is ideal for tracing live wiring connections, locating wiring breakage and

to distinguish between live or earth connections.

●Probe-Contact EF-Detection: For more precise indication of live wires, such as distinguishing between live and

ground sockets, use the Red (+) test probe for direct contact measurements.

-V and Ω of AutoCheck

In Manual Selection (AM-47 & AM-45 only)

From AutoCheck

with "Auto" being displayed, press the SELECT button momentarily 3 times to select ACV, 4

times to select DCV and 5 times to select Resistance (Ω) functions of AutoCheck

. Such selected function

remains auto-ranging.

-Frequency And Capacitance (AM-47 & AM-45 only)

From AutoCheck

with "Auto" being displayed, press the SELECT button momentarily 6 times to select

Frequency (Hz), 7 times to select Capacitance (F) functions and 8 times to return to AutoCheck

mode.

Note:

*Unlike the Line Level Hz Frequency function (for AM-47 only) as stated, this (Common) Hz Frequency function is

set only at the highest input sensitivity mainly for measuring small electronic signals of below 20VAC rms.

4-4) OTHER FUNCTIONS

-DCV, ACV & Line-Level Hz functions (AM-47 only)

Rotate the rotary selector to the V position selects common impedance (Hi-Z) voltage measurements. DCV is the

default function. Press SELECT button momentarily to select ACV. The AC annunciator "

" turns on. Press

momentarily again to activate the Line-Level Hz function.

Note:

*Line-Level Hz input sensitivity varies automatically with ACV range selected when Line-Level Hz is selected. AC

6V range has the highest and AC 600V range has the lowest sensitivity. Measuring the signal in ACV function

WHILE selecting Line-Level Hz function in that ACV range automatically sets the most appropriate sensitivity for

higher voltage applications. This can avoid electrical noises as in 110/220V line voltage applications for example.

If the reading shows zero due to insufficient signal levels, select Line-Level Hz function BEFORE making

measurements (at AC 6V range) will set the highest sensitivity.

-Diode & 600Ω functions (AM-47 only)

Rotate the rotary selector to the

/600Ω position.

Diode test is the default function. The reading shows the approximate voltage drop across the test leads. Normal

forward voltage drop (forward biased) for a good silicon diode is between 0.400V to 0.900V. A reading higher than

that indicates a leaky diode (defective). A zero reading indicates a shorted diode (defective), and the meter will

give a long beep as continuity warning. An OL indicates an open diode (defective). Reverse the test leads

connections (reverse biased) across the diode. The digital display shows OL if the diode is good. Any other

readings indicate the diode is resistive or shorted (defective).

Press SELECT button momentarily selects the lowest 600Ω range for lower resistance measurements. It is an

extended range to complement the AutoCheck

Resistance (Ω) function.

-DC-µA & AC-µA Micro-Amp functions (AM-47 only)

Rotate the rotary selector to the µA position. The display-reading unit is in µA although there is no unit

annunciator on the display. DC-µA is the default function. There is no annunciator for DC. Press SELECT button

momentarily to select AC-µA. The AC annunciator "

" turns on. These ranges, like other functions, are

protected up to the maximum rated voltages of the meter.