1byone O00QH-0511 User Manual - Page 3

Browse online or download pdf User Manual for Accessories 1byone O00QH-0511. 1byone O00QH-0511 9 pages. Wireless door chime kits

Print Page

Receiver Unit

Drill two holes on the wall at your required height. The distance between

the two holes should match the two hanging holes at the back of the

receiver.

Then insert two wall plugs (included) into the holes.

After that, insert two screws (included) into the wall plugs.

Be noted that you should not insert completely the screws

into the wall plug, but keep a suitable length out of the wall

surface, which is to hold the receiver.

Finally you can hang the receiver.

Avoid positioning on UPVC Frames, above heat sources (e.g. radiator) or in damp areas such as a

kitchen or bathroom.

Installation

Install the PIR transmitter in channels through by cars or on wall of the indoor main channels or

key monitoring area. During installation, pay attention to the followings: avoid direct sunlight;

don't be in face of glass doors and windows; don't be opposite to cold and hot air vents or sources;

and don't be opposite to any easy oscillation. The recommended installation height is 1.0m-1.5m,

adjusting the angle to make it face the monitoring area. If a car or a person moves into the detection

range of the PIR transmitter; the PIR transmitter will send a signal to the receiver. The receiver makes

ding-dong or alarm sound after receiving the signal to warn the master.

Functions Instruction

1. Install the PIR Transmitter with three AAA alkaline batteries.It turns into induction state after 10

seconds power-on,with induction time interval 5 seconds.

2. Install the receiver with three 1.5V type "C" alkaline batteries or plug the receiver into DC6V

200mA power. Move the On/Off Switch to the ON position. Maximum 50 codes can be matched

and saved in the receiver within 15 seconds. After 15 seconds, the receiver turns into power saving

mode.

Note: If there is no code matched and saved within the first 15s, the receiver can be matched with

and save ONLY one code after 15s.

3. When there is a code saved within the receiver, you need not to match the code the second time

you turn on the power, as the receiver will come directly into alarm state or chime state.

4. If you want to add PIR Transmitter or magnetic transmitter, press the auto-learning code button

on the side of the Receiver once, then trigger the PIR Transmitter or magnetic transmitter. The

Receiver will sound to indicate that the transmitter works successfully with the Receiver. (Press the

button once can only match one transmitter).

5. Press the auto-learning code button and hold for 5 seconds, you can delete all the information

within the receiver. At the same time, the LED indicator light will flash and receiver sounds.

6. There is a Sound and Flash Switch Button on the side of the receiver. Press this button for three

options, working only with sound, only LED flash, sound and LED flash.

7. Low voltage indication: normal voltage for the receiver 3.08V±0.1V and for the transmitter

3.08V±0.1V. If lower than this voltage, the LED indicator light will flash once every second to

remind you to change the batteries.

8.There is one Chime-Low-Alarm switch on the side of the receiver. It operates as follows: High

Volume Chime/ Low Volume Chime / Alarm.

9. Move the Chime-Low-Alarm switch to Chime or Low position the receiver will work as a chime.

Move the switch to Alarm position, it will work as an Alarm.

10.The receiver batteries' lifespan: if a 1.5V C battery with capacity 7800mAh is used, based on

average 10 sounds per day, 80% of the battery capacity available, these three batteries can be

used for 20 months.

11.The PIR transmitter batteries' lifespan: if a 1.5V AAA battery with capacity 1150mAh is used,

based on average 10 sounds per day, 80% of the battery capacity available, these three batteries

can be used for 12 months.