Dragonfly DFM-TAB-92 Owner's Manual - Page 8

Browse online or download pdf Owner's Manual for Projection Screen Dragonfly DFM-TAB-92. Dragonfly DFM-TAB-92 8 pages. Dfm-tab screens
Also for Dragonfly DFM-TAB-92: Installation Manual (17 pages)

Print Page

SCREEN DIMENSIONS

TROUBLESHOOTING

Dragonfly motorized film screens are designed to function trouble-free for years of enjoyment. Most problems that occur are due to simple

issues. If you have trouble, please check the list of simple fixes below. If the problem persists, contact your authorized Dragonfly dealer or

Dragonfly customer service at [email protected]

Screen does not react to any control

Screen goes lower than desired or does

not retract far enough

IR control does not work

For Technical Support: 1.866.838.5052

2-Year Limited warranty

Dragonfly Motorized and Tab-Tension Motorized Film Screens have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be

defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be

repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).

Model

DFM-TAB-84

4.99"

93.07"

4.72"

DFM-TAB-92

4.99"

99.96"

4.72"

DFM-TAB-100

4.99"

107.00"

4.72"

DFM-TAB-106

4.99"

112.20"

4.72"

DFM-TAB-110

4.99"

115.78"

4.72"

DFM-TAB-120

4.99"

124.41"

4.72"

DFM-TAB-84-43

4.99"

87.05"

4.72"

DFM-TAB-92-43

4.99"

93.42"

4.72"

•Power cable to the film screen is incorrectly connected or plugged into an outlet that does not have power.

•Check connections and verify power on the outlet.

•Check control method selected (IR, wall-pad or low voltage) and try an alternate method.

•Adjust the up and down limits as described in "Adjusting your Dragonfly motorized film screen".

•Check the batteries in the IR remote that you are using.

•Ensure that you are within range of the remote being used. The factory remote will work at a distance of

up to 15' in most situations.

•Ensure that the connector for the Tab IR sensor is fully seated if that is the method you are using and that

the IR emitter you are using (if applicable) is wired and operating properly.

•If you have chosen to 'hard-wire' the IR connection into a RJ-11 connector, be sure that you have the

appropriate wires on the correct pins, as described in the "IR Control" section.

41.14"

73.23"

60.23"

83.73"

45.01"

80.19"

64.17"

90.7"

49.01"

87.16"

68.11"

97.67"

51.97"

92.40"

71.06"

102.87"

53.90"

95.86"

73.00"

106.37"

58.82"

104.56"

77.90"

115.14"

50.39"

67.20"

69.49"

77.71"

55.20"

73.58"

72.29"

84.09"

up to 21"

4.92"

4.72"

86.69"

up to 21"

4.92"

4.72"

93.66"

up to 21"

4.92"

4.72"

99.92"

up to 21"

4.92"

4.72"

105.12"

up to 21"

4.92"

4.72"

108.62"

up to 21"

4.92"

4.72"

117.39"

up to 21"

4.92"

4.72"

79.96"

up to 21"

4.92"

4.72"

86.34"