Bosch FAP-OC 500Series Service Manual - Page 28

Browse online or download pdf Service Manual for Washer Bosch FAP-OC 500Series. Bosch FAP-OC 500Series 41 pages. Built-in wall ovens
Also for Bosch FAP-OC 500Series: Installation Instructions Manual (21 pages), Instructions For Use Manual (40 pages), Installation Manual (6 pages), Product Information (40 pages), Installation Manual (28 pages), User Manual (48 pages), User Manual (48 pages), Installation Manual (28 pages), Use And Care Manual (44 pages), Installation Manual (32 pages), Use And Care Manual / Installation Instructions (40 pages), Quick Reference Manual (4 pages), Use And Care Manual (27 pages), Installation Manual (24 pages), Installation Manual (32 pages), Use And Care Manual (24 pages), Installation Manual (28 pages), Use And Care Manual (21 pages), Installation Manual (32 pages), Service Manual (36 pages), Installation Manual (32 pages), Quick Start And Safety Manual (13 pages)

Print Page
Bosch FAP-OC 500Series Service Manual
58300000202181 ARA EN B
Error Code Description
E009
ROM-check error in user interface
E309
E010
Data memory error in user
E310
interface
Continuous pushing of a single key
E011
(E411 internal error reported as
E011)
Defective control module
E312
temperature sensor
E314
Cancel / Off key error
E414
Continuous pushing of multiple
E032
keys
(E432 internal error reported as
E032.)
Touch control module (TCM)
E044
option code error
Copyright by BSH Home Appliances Corporation
This material is intended f or the sole use of BSH authorized persons and may contain conf idential and proprietary inf ormation. Any unauthorized rev iew, use, copy ing, disclosure, or distribution in any f ormat is prohibited.
Novemb er 2018
Cause/Notes
ROM-check performed at reset fails. All
heating elements disabled. Error will be
cancelled at start-up if next ROM-check
succeeds.
Cyclic check of memory content or a write to
memory failed. All heating elements will be
disabled. Error will be cancelled at start-up.
Key pressed continually for 10 seconds, or
touchpad assembly has a bad key. Heating will
be stopped and will resume when key is no
longer pressed.
All oven operations suspended until control
reset
Oven operation will be stopped. Error
cancelled only by a system reset.
Two or more keys continuously pressed for 10
seconds or touch pad assembly has more than
one bad key. Key actions are suspended and
heating is paused. Error will clear and normal
operation will resume when no touch pads are
depressed.
TCM board or connections to TCM are bad.
During start-up, the control module is unable
to set TCM option code. Reset is required to
clear error.
1901 Main St ▪ Suite 600 ▪ Irvine, CA 92614
Service Manual for Bosch 500 Series Built-in Wall Ovens
Suggested Action(s)
 E009: Replace user interface
 E309: Replace control module
 E010: Replace user interface
 E310: Replace control module
 Confirm touch panel is clean and free of
moisture, oils or other contaminants.
 Inspect user interface PCB.
 Check door seal to verify vapor/moisture is
not causing key activation; replace seal if
necessary. Run Key Test in Service mode; if
it fails, replace front panel assembly.
Replace control module
 Check touch pad assembly.
 Inspect user interface PCB.
 Confirm touch panel is clean and free of
moisture, oils or other contaminants.
 Inspect user interface PCB.
 Check door seal to verify vapor/moisture is
not causing key activation; replace seal if
necessary. Run Key Test in Service mode; if
it fails, replace front panel assembly.
 Enter Service mode to set correct option
code.
 Check connection to control module.
 Check connection to TCM.
 If unable to set option code and
connections are good, replace front panel
assembly.
Page 28 of 41
800 944-2904