Draper 220V Ultimate Access Installation And Operating Instructions

Browse online or download pdf Installation And Operating Instructions for Projection Screen Draper 220V Ultimate Access. Draper 220V Ultimate Access 4 pages. Electric projection screen

Print Page

220V Ultimate Access Electric Projection Screen by Draper

These Installation/Operating Instructions are available in the official language

of the country where you purchase the product. Please contact your distributor

to request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue officielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

1 Read instructions through completely before proceeding.

Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

Entire bottom of screen case should be unobstructed to permit

access to bottom panel for electrical connections or servicing.

Screen should be installed level (using a carpenter's level).

Nothing should be fastened to screen dowel or viewing surface.

Operating switch(es) and mounting brackets are packed separately

in screen carton. Do not discard with packing material.

Screen operates on 220 V AC, 50 Hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any responsibility

on the part of the manufacturer for improper installation or faulty workmanship at

the jobsite.

Hanging Screen

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in the length of the case.

Screen is normally recessed above ceiling and may be installed in a variety

of ways. See typical installations detailed on page 3. Regardless of mounting

method used, the following points apply:

1 Mounting brackets are packed separately in carton. Engage each

bracket with top of housing as shown below and tighten set screws. A

bracket should be within 46 cm from each end of screen case. Brackets

can be removed and case mounted with lag screws through top of case

(holes drilled on site).

2 Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken installation.

3 Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen.

4 Entire bottom of case must be readily accessible after installation is

complete.

Remove shipping brackets

before operating screen.

Slots along top of case permit

brackets to be set at an angle

Typical Installation

" electrical cutout

Form UltimateAccess220V_Inst13

Installation/Operating Instructions

Caution

Shipping

Bracket

Alternate

Installation

(additional

set of brack-

ets required

but not in-

cluded)

Case dimensions

on page 4.

Printed in U.S.A.

5 The bottom access panel, trap door, and lower edge of the case are

joined with continuous hinge joints and must operate freely. Front and

back of case must be straight–not forced to warp or bow. Hinge joints

must be free of mastic or paint build up, and trapdoor and access panel

must be unobstructed by ceiling tiles.

6 If case is painted on location, removal of roller/fabric assembly is

recommended prior to painting. If not removed, slots on bottom of case

should be shielded to protect viewing surface from paint splatters or

overspray.

7 Do not seal unit in ceiling until electrical connections have been made

and screen has been operated successfully.

Screen operates on 220 V AC, 50 Hz. current.

Junction box is located just above the bottom access panel at left end of

screen.

Open the access panel/trap door for access to the junction box cover. (See

bottom access panel/trap door opening and closing instructions below).

Remove two (2) hex head screws that secure the cover to the junction box to

expose the brown, black, and blue pigtail leads and the green ground wire per

wiring diagram on page 4.

If optional low voltage control or video interface control is specified and factory

installed, please refer to wiring diagram on page 4.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is connected.

Bottom Access Panel/Trap Door Opening & Closing

After screen case has been mounted, remove the dowel shipping brackets

from dowel if provided. A spring latch at each end of the trap door holds

this assembly closed. In some screens there will also be a spring latch

near the center of the case. To gain access to inside of screen case, disen-

gage spring latch at each end of the case (and near the center of the case, if

applicable) by sliding the latch lever towards the center of screen case, then

pull down slightly on the trap door assembly. The latch levers are somewhat

concealed from view. Locate these with the trap door open by feeling for the

vertical latch lever above the door about 8 cm from case endcaps and near

the center of the case.

The assembly will swing down, opening about 135°. Pivot the prop arms at

each end of the trap door assembly towards the ends of screen case. Prop

Dowel

arms engage with a hole in each endcap to hold the trap door assembly fully

open. To close the trap door assembly disengage prop arms from endcaps

and pivot these over the access panel. Swing the trap door assembly upward,

stopping just before the latch levers hit the bottom flanges of the endcaps

(and center of case where appropriate). Pull levers of latches towards center

of screen case to allow the trap door assembly to be pivoted to its closed po-

sition. Make sure that the spring latch levers engage fully with case endcaps

(and center of case where appropriate).

Caution: Beware of pinch

points along closure

If you encounter any difficulties installing or servicing your Ultimate Access screen, call

your dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-1689.

US Patent Nos. 5,341,241; 6,137,629;

6,421,175; 6,532,109; 6,816,308; 7,559,707

Electrical Connections