Draper Baronet HW Installation & Operating Instructions - Page 2
Browse online or download pdf Installation & Operating Instructions for Projection Screen Draper Baronet HW. Draper Baronet HW 2 pages. 110v and 220v electric projection screen
Print Page
Baronet/HW by Draper
Please Note: Do not wire motors in parallel.
Baronet/HW 110V AC
Single Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Motor Ground)
Control
Single gang box by others
switch
Min. 4" x 2-1/8" x 1-7/8" deep
Blue
Red
Black
Dashed wiring
by electrician
Location of key
operated on-off
switch if furnished
To 110V AC Line
Low Voltage, IR Remote or RF Remote (LVC-III)
110-120V 3-Position Wall Switch
3
7 mm (2
/
")
4
UP
11.8 mm
(4
1
/
")
2
DOWN
Case Dimensions
3¼"
(83 mm)
3¼"
3¾"
(83 mm)
96 mm
Wiring Diagrams
Multiple Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Motor Ground)
Cap off with wire
Red
Blue
nut and tape
Black
Dashed wiring
by electrician
Red
Blue
Black
Red
Blue
Single gang box by others
Black
Min. 4" x 2-1/8" x 1-7/8" deep.
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110V AC Line
Internal Screen Wiring
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
STOP
3 Button Wall Switch
DOWN - Black
COM - White
STOP
UP - Red
Control
Aux Port for connecting additional LVC-III
Switches
modules (up to six total can be linked-
24v DC
connect from Aux to Eye).
3"-6" leads
www.draperinc.com
Fabric width + 5¾" (146 mm)
Viewing
Surface
Single Station Control
CE Approved
Junction box at
eft end of screen
Control
switch
Dashed wiring
by installer
See separate Serial Communication-RS232 Instruction sheet for
White/Blue (Common)
Red 110/Black 220 (Up)
enabling RS232 with the MC1.
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
To
110/220V
Line
Location of key
Fuse
operated on-off
switch if furnished
MC1
220V 3-Position, Surface Mount Wall Switch
(765) 987-7999
Baronet/HW 220V AC (CE)
Multiple Station Control
Junction box at
left end of screen
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Green/Yellow (Motor Ground)
Red
Black
Red
Black
Red
Black
220v,
50 Hz.
220v, 50 Hz.
MC1
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Program LED
Green/Yellow-Ground
Low Voltage Wiring by others
AC Wiring by electrician
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
3
4.5 mm (1
/
")
4
8.6 mm
3
(3
/
")
8
Page 2 of 2
Not CE Approved
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Green/Yellow (Motor Ground)
Cap off with wire
nut & tape
Blue
Blue
Blue
Dashed wiring
by installer
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green 110V/
Green/Yellow 220V
(Motor Ground)
Location of key
operated on-off
switch if furnished
To AC Line
1
3.8 mm (1
/
")
2
1
3.2 mm (1
/
")
4
7.8 mm
1
(3
/
")
16