Exterior Motorized FlexShade
Section 6 - Limit Switch Adjustments
Sonesse 120V Motor
Caution: Unit ships without limits. Limits will need to be
set before the unit is operated. Always be prepared to
shut off manually when new adjustment is being tested.
Push Button Limits
1. Fully depress both limit switch push buttons, then
operate wall switch to make sure system works
properly.
2. Raise shade to desired "UP" stop position.
3. Set upper limit by depressing proper
push button.
(back)
4. Lower shade to desired "DOWN" stop position.
5. Set lower limit by depressing proper
button.
Screw-Type Limits
6. Determine which direction of fabric travel corresponds with arrows on motor.
7. Operate shade to desired "down" stop position.
Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.
8. Operate shade to desired "up" stopping position.
Set limit by turning proper screw toward "-" to raise limit, and "+" to lower it.
Please Note: Each full rotation of the limit screw equals approximately 5/ 8 "
require rotating the limit screw several times.
Caution: DO NOT allow the hem bar to hit the upper roller or fascia. This will damage the unit.
Section 7 - Complete Electrical Connection
Operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch
lead
. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to
(standard)
connect shade to switch
and switch
(es)
diagram, and wiring should comply with national and local electrical codes.
DO NOT wire motors in parallel without written permission from Draper
All operating switches should be "off" before power is connected.
Sonesse
Please Note:
Quick disconnect and NEMA 3
prong plugs provided by others.
push
(front)
to power supply should be furnished by installer. Connections should be made in accordance with attached wiring
(es)
Controls & System Overview
RTS 120VAC Motors
®
RTS
MOTOR
120V
Patio
RF Remote
B W G
STOP
Decora RTS
Wireless Keypad
110-120V Line
Dashed Wiring
by Electrician
Sonesse
is a registered trademark of Somfy
®
®
Caution:
- Be sure all switches are in
"off" position before adjusting
limit switches.
- Shade may be damaged by
running shade fabric up too
far and exposing roller.
- If using a group control
system, each limit switch
must be set prior to
connecting to system.
- Motor must be installed so
limit switches are pointed
down or accessible.
of shade travel, which may
(16mm)
.
®
Controls & System Overview
Sonesse
W B R G
110-120V Line
Systems, Inc.
®
ROOM SIDE
Front
Back
GLASS SIDE
PUSH BUTTON LIMITS
ROOM SIDE
ROOM SIDE
Front
Front
Back
Back
GLASS SIDE
Bottom View
GLASS SIDE
SCREW-TYPE LIMITS
ROOM SIDE
+
ROOM SIDE
Front
Side View
+
Front
Back
+
Screws
Back
GLASS SIDE
+
Bottom View
GLASS SIDE
Bottom View
Screws
Side View
Screws
Side View
fully boxed, and supplied with a 6'
(es)
120VAC Motors
®
NOTE: Test shade operation
120V
If shade direction does not
MOTOR
correspond with the switch
orientation, turn power back
off and switch the red and black
wires from the motor to the switch.
Do not wire motors in parallel without
written permission from Draper.
Control
Switch
Single Gang
B
Box (by others)
Dashed Wiring
by Electrician
page 7 of 12
Standard right-hand
Bottom View
motor configuration shown
+
+
Side View
Standard right-hand
Bottom View
motor configuration shown
Side View
cable
(183cm)
Print Page