Draper Premier Installation & Operating Instructions - Page 3

Browse online or download pdf Installation & Operating Instructions for Projection Screen Draper Premier. Draper Premier 4 pages. 220v premier electric projection screen
Also for Draper Premier: Installation & Operating Instructions (2 pages), Installation & Operating Instructions (2 pages), Installation Instructions (2 pages), Instructions Installation & Operation (7 pages), Installation Instructions (4 pages), Installation Instructions (2 pages), Installation Instructions (2 pages), Installation & Operating Instructions Manual (7 pages)

Print Page

Draper Premier Installation & Operating Instructions

Targa and Premier—Large Sizes by Draper

Draper's Tab-Tensioning System is factory-set, and under normal circumstances will not require field adjustment.

If, however, you notice wrinkles, waves or other indications that the tensioning cables need to be adjusted, follow the procedure below.

1 Determine which side requires adjustment.

2 Secure dowel with one hand.

3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw and slowly turn CLOCKWISE TO INCREASE tension,

or COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in ¼ turn increments. Adjust only one increment (¼ turn) at a time

4 If problem is not corrected, leave screen in position for 24 hours to allow surface material to stretch into position.

5 If problem still is not corrected, repeat steps 2 and 3.

Caution: Do not touch

or bend surface.

Limit Adjustments (Standard/Quiet Motors)

Please Note: Screen limits are factory set for optimum performance of the

screen. Any adjustment of these limits could void the warranty. Please

check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches.

Adjusting "fully up" position —You should never have to adjust this

limit! If you do, however, the "Up" stopping position may be adjusted by turn-

ing the yellow limit switch adjustment socket. The yellow socket is located on

left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm

"). Turning the socket counterclockwise will allow the viewing surface to

retract farther into the case. Turning it clockwise will cause the surface to stop

farther out of the case. One full revolution of the socket will alter the stopping

position of the viewing surface by approximately 1½".

Adjusting "fully down" position — "Down" stopping position may be ad-

justed by turning the white limit switch adjustment socket. The white socket

is located on the left end of screen roller and is accessible to a screwdriver/

Allen wrench (4mm or

"). Turning the socket counterclockwise will allow the

viewing surface to run farther down. Turning it clockwise will shorten the view-

ing surface, causing it to stop in a less extended position. At no time should

viewing surface be unrolled enough to expose any part of screen roller.

Accessing Built-In Low Voltage Control Unit (LVC-IV)

To access the Built-In LVC-IV

1 Remove the two (2) Torx head

screws from the motor end of

the screen housing.

2 Remove the access panel

with the LVC-IV from the

screen housing.

Remove two (2)

Torx head screws

from endcap

Tab-Tension Adjustment Procedure

DOWEL

Remove

access panel

with LVC IV

www.draperinc.com

TENSIONING

CABLE

ADJUSTMENT

SCREW

DOWEL

Limit Adjustments (Built-in Low Voltage Motors)

Please Note: Screen limits are factory set for optimum performance of the

screen. Any adjustment of these limits could void the warranty. Please

check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches.

(Height adjustments are made from wall switch)

1 Connect the ILT switch to the motor via the terminal blocks, or via the

modular port using four conductor modular cable. When using modular

cable, the cable connectors MUST NOT be crimped in reverse, as with

standard telephone cable.

2 Set the slide switch to the lower position. Press and hold the DOWN button

on the switch to move the viewing surface to the desired lower limit. If the

screen moves in the opposite direction, release the DOWN button and

press and hold down the STOP button for four seconds. This will reverse

the operation of the UP and DOWN switches.

3 Move slider switch into center position. Wait a couple of seconds.

To Motor

with

Built-In

Low Voltage

Slide

Switch

To Motor

with

Built-In

Low Voltage

Back View

Please Note: If you move the slider switch from down to up in one mo-

FUNCTION

POSITION

tion it sets the two limits in the same position.

4 Set the slide switch to the higher position. Move the viewing surface to the

Set LOWER limit

DOWN

desired upper limit by pressing and holding the UP button on the wall

Set UPPER limit

switch.

5 Return the slide switch to the center position to return to normal operation.

Normal Operation

CENTER

(765) 987-7999

Page 3 of 4