Draper Salara Installation Instructions

Browse online or download pdf Installation Instructions for Projection Screen Draper Salara. Draper Salara 2 pages. 220v ir plug & play
Also for Draper Salara: Quick Manual (2 pages), Installation Instructions (2 pages), Installation Instructions (2 pages)

Print Page

These Installation/Operating Instructions are available in the ofﬁ cial

language of the country where you purchase the product. Please contact your

distributor to request a copy.

Vous pourriez demander les instructions d'installation et d'opération

traduises dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in

der ofﬁ ziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

➀

Read instructions through completely before proceeding.

➁

Follow instructions carefully. Installation con trary to instructions in val i-

dates warranty.

➂

Screen should be accessible for complete removal should fabric

become damaged or should other ser vice be required.

➃

Screen should be installed level (using a carpenter's level).

➄

Nothing should be fastened to screen dowel or viewing surface.

➅

Operating switch (es) packed separately in screen carton. Do not

discard with packing material.

➆

Screen operates on 220V AC, 50 Hz., 1 ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Wall/Ceiling Flush Mounting

➀ Attach Mounting Brackets to wall or ceiling (see Fig. 1). The installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required

by the mounting surface. Installer also needs to ensure the mounting

surface is reinforced sufﬁ ciently to support the screen. Brackets must be

level with each other.

Mounting

Bracket

Wall

➁ Plug the power cord (included if ordered) into the motor end of the screen

case (left end as the viewer sees the screen).

➂ Attach the screen by snapping the extrusions on the back of the case onto

the brackets. With the lower edge of the screen case tilted away from the

wall, engage the rib on top of the case with the slot on each bracket. Slide

the screen case along the brackets to adjust the screen location from left to

right if necessary (see Fig. 2). Once the case is in position, pivot the case

back toward the brackets until the lower edge of the case "snaps" into place

with the spring-loaded latch (see Fig. 3).

Installation Instructions

220V IR Plug & Play Salara by Draper

Caution

Ceiling

Mounting

Bracket

Figure 1

Extrusions along

back of case

Electrical Connections

Screen operates on 220V AC, 50 Hz., 1 ph. current. Screen shipped with

internal wiring complete. Junction box is located inside left endcap and cover

plate is secured to endcap with one screw. Screen is shipped with internal

wiring complete and control switch(es) fully boxed. No external wiring is

needed. unless connecting to RS232. Plug cord into standard 220V AC outlet.

All operating switches should be "OFF" before power is connected.

Screen is equipped with a handheld remote or 3-position operating switch

(see below). Three positions (up-off-down) per mit operation to be stopped at

any point. Factory adjusted limit switches au to mat i cal ly stop screen when fully

down or fully up.

Wiring/Control Options:

Plug & Play

—

Provided with built-in IR receiver, handheld IR remote

control transmitter and 10' (3m) IEC cordset. No wiring necessary except to

connect to RS232.

Screen has been factory set and should not normally require further

adjustment. If you desire to change the "up" and "down" stopping positions,

follow the procedures below.

There are two holes in the left end cap (as seen from audience) for both limit

switch adjustments and neither is labled. The hole closest to the audience is

the up limit and the hole furthest from the audience is the down limit

"Down" limit switch: Down stopping position can be adjusted by turning

knob furthest from audience with a screw driver or hex wrench. Turning knob

counterclockwise will allow viewing surface to run farther down. Turning it

clockwise will reduce the amount of exposed viewing surface.

"Up" limit switch: You should never have to adjust this limit! If you do,

however, the Up stopping position can be adjusted by turning knob closest

to audience with a screw driver or hex wrench through the small grommet.

Turning knob counterclockwise will allow surface to run farther into screen

case. Turning it clockwise will allow viewing surface to stop farther out of

screen case.

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

If you encounter any difﬁ culty installing or ser vic ing your Salara, call your dealer

or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Figure 2

Figure 3

Operation

Adjustments

Dimensional drawings on page 2