Draper SLX14 Installation & Operation Instructions - Page 7

Browse online or download pdf Installation & Operation Instructions for Projection Screen Draper SLX14. Draper SLX14 8 pages. 230v ac scissor lift slx video projector lift
Also for Draper SLX14: Brochure & Specs (16 pages), Installation And Operation Manual (7 pages), Installation & Operating Instructions Manual (7 pages), Installation & Operating Instructions (4 pages), Installation & Operating Instructions Manual (7 pages)

Print Page

Draper SLX14 Installation & Operation Instructions

Scissor Lift - SLX 115V

Section 11 - Electrical Connections

Lift operates on 115V, 60 Hz. current. 14 amps current draw

Wire to connect lift to switch

and switch

(es)

Please Note: Lift must be installed in accordance with requirements of Local Building Codes, Canadian Electrical Code

Code

, NFPA 70. An appropriate disconnect device shall be provided as part of building installation.

(NEC)

CAUTION: All operating switches should be "off" before power is connected.

A junction box is provided for field connections. Unit ships with internal lift wiring complete. Use switch to lower lift and remove packing. Remove temporary wiring and

complete permanent wiring to electricity and to switches. Wire to connect unit to power supply and to switches should be furnished by installer. Connections should be

made in accordance with wiring diagram. Lift should be operated and checked prior to installing projector and/or optional ceiling closure.

Section 12 - Wiring Schematic

GN/YL

IR EYE

ENCODER CABLE

PAIRING

V in

GND

ENCODER CABLE

Section 13 - RS232 and RS485 Serial Port Protocols

Sending Lift Commands

START

ADDRESS

1 Char

2 Chars

XX = Decimal motor group address with range from 01 to 32.

Note it always has to be 2 characters,

so a 0 has to precede 1 digit addresses.

YYYYYY

= command from the following table:

EXAMPLES:

COMMAND

ACTION

L01R!

Move

Channel 1

L11E!

Move

Channel 11

(2 amps for lift, 12 amps for Outlet)

to power supply should be furnished by installer.

(es)

2 CONDUCTOR CABLES

ATTACHED TO

REAR SCISSOR

DOWN

Limit Switch

MODE

SWITCH

Limit Switch

GND

115Vac, 12A

50-60 Hz OUTLET

NOTES:

1. When the Optional Delay Feature is installed the Delay Switch must

be in the "Delay On" position for normal operation.

2. If the Optional Delay Feature is installed and the "Show" position requires adjusting

the "Delay Switch" must be switched to "Off" while adjusting the show position

3. Refer to the "Adjusting" section on page 4 of these instructions

for information on how to adjust the "Show" position.

COMMAND

END

1 - 6 Chars

1 Char

YYYYYY

COM Port Settings:

Port Speed:

Data Bits

to Fully

Retracted.

Parity

to Fully

Extended.

Stop Bits

Flow Control

Lift ships with internal wiring complete and control switch

MOTOR

DOWN

Delay Switch

RUN CAP

45 MFD

(on position)

GN/YL

Dashed wiring by electrician

Low voltage wiring by others

ENCODER

9600 baud

NONE

X On / X Off

, CAN/CSA C22.1 and National Electric

(CEC)

Attached to

Optional Delay Assembly

lower pan

115VAC

ALTERNATE 'UP' LIMIT SWITCH WIRING

Power Supply

*Black

Jumper wire is located in the

(BK)

plastic sleeve with these instructions.

NOTE : Jumper CANNOT be used when lift

is installed in Environmental Air Space

Housing and Optional Ceiling Closure

COMMAND

FULLY EXTEND

FULLY RETRACT

STOP

SP1

Go to FIRST show position

SP2

Go to SECOND show position

PREVIOUS show position

NEXT show position

ADD show position

ADDSP

DELETE show position

DELSP

Identify channel

SET

SET splitter board channel

ADD

ADD a communication channel

DEL

DELETE a communication channel

FS1

Restore MAIN BOARD to Factory Settings

FS2

Restore SPLITTER BOARD to Factory Settings

FS0

TILT to PREVIOUS STOP

GETFV1

Get MAIN BOARD Firmware Version Number

GETFV2

Get SPLITTER BOARD Firmware Version Number

page 7 of 8

fully boxed.

(es)

COM

N.O.

N.C.

Limit

Switch

Jumper*

ACTION

(Setting main board)