Draper SLX17 Installation And Operation Manual

Browse online or download pdf Installation And Operation Manual for Projection Screen Draper SLX17. Draper SLX17 7 pages. 230v ac scissor lift slx video projector lift
Also for Draper SLX17: Brochure & Specs (16 pages), Installation & Operating Instructions Manual (7 pages), Installation & Operation Instructions (8 pages), Installation & Operating Instructions Manual (7 pages)

Print Page

Draper SLX17 Installation And Operation Manual

SLX Scissor Lift Video Projector Lift by Draper

① Read instructions completely before proceeding.

② Test lift prior to installation.

③ Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

④ Do not obstruct operation of Scissor Lift SLX with ﬁ ngers or any object.

Serious injury or damage could result.

⑤ Maximum lifting capacity is 350 Lbs.

⑥ Scissor Lift SLX is designed to accommodate ceiling suspended

equip ment. Equipment should not be allowed to rest on optional ceiling

closure during operation (refer to section titled "Installing Pro jec tor").

⑦ Entire bottom of unit must be unobstructed to permit proper op er a tion.

Sufﬁ cient clearance must be allowed below projector or op tion al ceiling

closure: 10' for Model SLX10, 14' for Model SLX14, etc.

⑧ Unit must be installed level (use a carpenter's level).

⑨ Unit operates on 110-120V AC 60 Hz. current.

⑩ Verify the show position when testing lift. Make required changes by

referring to adjustment instructions on page 4 of this document.

CAUTION: Before servicing unit, disconnect hardwired control and

any remote control.

Note: Unit has been thoroughly inspected and tested at factory and found

to be operating properly prior to shipment.

① Based on screen location and projector speciﬁ cations, determine proper

position for projector in stal la tion.

② Conﬁ rm that there is adequate space for installation and operation.

Minimum clear ance above ceiling level varies according to Scissor Lift

model, plus height of projector, optional mounting bracket, optional ceiling

closure, and optional Environmental Air Space Housing.

③ Arrange to provide service access to the unit.

④ Maximum lifting capacity is 350 Lbs.

As Soon As Scissor Lift Arrives

① Open carton and inspect for damage.

② Locate the following parts:

A. The unit itself

B. Controls

C. Optional equipment: Environmental Air Space Housing, Universal

Projector Mount, closure panel or ceiling ﬁ nish kit (all ship in separate

cartons).

③ Test lift prior to installation.

Hanging Unit

Please note: If using Environmental Air Space Housing option, go to

Environmental Air Space Housing instructions on page 3.

The Scissor Lift may be installed in a variety of ways; recessed above

the ceiling, or sus pend ed below the ceiling. The lift should be supported by

four ½" thread ed mount ing rods. If ceiling recessed, the entire unit (including

the projector) should set approximately 1½" above the ﬁ n ished ceiling in its

"stored" position. The threaded rods should pass through the corner mount ing

ﬂ anges and be secured by nuts above and below. The unit should then be guy

wired or blocked to pre vent swing ing.

All installations should observe the following guidelines:

① If installing above a hard ceiling, optional Draper Access Panels are

available to allow access to the unit.

② Installer must ensure that all fasteners and supports are of ad e quate

strength to securely support Scissor Lift and projector.

③ Fastening methods must be suitable for mounting surface, and se cure ly

anchored so that vibration or abusive pulling on unit will not weaken

installation.

④ Unit should be level, with weight shared more or less equally by all four

threaded mount ing rods.

⑤ Bottom of unit must be unobstructed after installation. Sufﬁ cient clear ance

must be allowed below projector or optional ceiling closure.

Caution: Beware

of pinch points

Installation/Operating Instructions

Caution:

Planning

⑥ Do not use unit to support adjacent ceiling, light ﬁ xtures, etc.

⑦ Do not complete the ceiling below unit until electrical connections have

been completed and unit has been operated successfully.

⑧ We recommend that safety cables be attached to the Scissor Lift SLX for

added security (a sound in stal la tion practice with overhead equipment).

⑨ When the Scissor Lift SLX is to be installed in "other space used for

environmental air" the optional environmental air space housing must

be installed per instructions to isolate the lift from the "other space

used for environmental air."

Electrical Connections

Unit operates on 110-120V AC, 60 Hz. current.

Opening the electrical box ex poses ter mi nals for ﬁ eld con nec tions. Unit

is shipped with internal wiring com plete.Wire to connect unit to power

supply should be furnished by in stall er. Con nec tions should be made in

accordance with wiring di a gram, and wiring should com ply with na tion al and

local elec tri cal codes. All op er at ing switches should be "off" before power is

con nect ed.

Caution: Make sure electrical supply has been disconnected before

attempting to connect Scissor Lift to electricity.

Scissor Lift should be operated and checked prior to installing pro jec tor and/or

optional ceiling closure.

Low Voltage Control Switch shown below comes with 75' of cable and should

be plugged in to Control Panel on top frame of lift for control of the "Closed"

and "Show" positions. Momentary Key Switch shown below comes with 75' of

cable and should be plugged in to Control Panel on top frame of lift for control

of the "Service" position.

LVC-S

Closed & Show

When unit is ﬁ rst operated, be cautious! If unit fails to operate when the

"down" button is pressed, press "off" and recheck elec tri cal con nec tions before

pro ceed ing. Cycle unit down and up several times to conﬁ rm sat is fac to ry

operation.

Caution: Do not pull on or touch safety belt when unit is in motion. If belt

locks, the cables will unspool.

Caution: Obstructing bottom pan may cause cables to unspool.

Standard Single Station Control (See Fig. 1)—One three-button switch with

"up", "down", and "off" buttons. Lift starts up or down when ap pro pri ate button is

pressed, and may be stopped by pressing "off" button. Factory set limit switch es

stop lift automatically when pro jec tor is in "show" position. One momentary key

switch lowers lift from "show" to "service" position.

Optional Multiple Station Control—Optional, moves lift from "stored" to "show"

position only. Each switch ing station has a three-button switch with "up", "down",

and "off" buttons. Lift starts up or down when ap pro pri ate button is pressed,

and may be stopped by pressing "off" button. Factory set limit switch es stop lift

automatically when pro jec tor is in "show" position.

Optional Key Operated Switch—If ordered, the standard LVC-S can be replaced

with a second single station, momentary key-operated three position (up/off/down)

switch. Multiple Station Control re quired for this option. Moves lift from "stored" to

"show" position only.

Optional Infrared or Radio Frequency Remote Control—If ordered, a three-

button transmitter is provided, with "up", "down", and "stop" buttons. Unit starts up

or down when appropriate button is pressed, and may be stopped by pressing

"off" button. Factory set limit switches stop unit au to mat i cal ly when projector is in

"show" po si tion. Only controls "show" and "stored" positions.

Optional RS232 Control—For Serial communication an R2D7 Serial

Communications Interface is optionally available.

Low Voltage Trigger—Input provided for Low Voltage Trigger from projector (see

diagram on page 4).

Please Note: Scissor Lift SLX must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA

C22.1 and the National Electric Code (NEC), NFPA 70, as required. An appropriate

disconnect device shall be provided as part of the building installation.

If you encounter any difﬁ culties installing or servicing your Scissor Lift, call your dealer

or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.

SP-KSM

Service

OFF

DOWN

Figure 1

Operation