Draper Targa Installation & Operating Instructions

Print Page

Draper Targa Installation & Operating Instructions

➀

Read instructions through completely before proceeding.

➁

Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

➂

Screen should be accessible for complete removal should fabric

become damaged or should other service be required.

➃

Screen should be installed level (using a carpenter's level).

➄

Nothing should be fastened to screen dowel or viewing surface.

➅

Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

➆

Screen operates on 110-120v, 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Hanging Screen

General:

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in case. Handle case carefully to protect its finish.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. S-hooks are included

with screen. Chains (or cable) and turnbuckles should be provided by in-

staller. Chains should be attached to beams or other structural members.

Turnbuckles should be adjusted so screen hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. No. 12 screws for

wood or aluminum are provided. However, if screen attaches to plaster,

gypsum board or masonry, installer should furnish toggle bolts, molly bolts,

nylon or lead anchors as required.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may

be mounted as in suspended or wall installation.

Please see back page for types of installation

" hole for

electrical

connection.

Mounting angle

and hardware

by others.

Suggested for

recessed installations.

Installation/Operating Instructions

Targa Electric Projection Screen by Draper

Caution

Fasteners for

wall mounting

by others.

S Hooks for

suspended installation.

Form Targa_Inst02

Screen operates on 110-120v, 60 hz. current.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws. Junction box contains red, black and white pigtail leads and

green internal ground wire, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with National and

local electrical codes.

All operating switches should be "off" before power is connected.

Before operating screen remove tape securing fabric and dowel to roller. If

viewing surface hangs out of case 8 " or 9 " , tape has probably been broken

by rough handling in shipment, allowing surface to "unwrap" one turn about

the roller. Manually wrap fabric back around the roller without turning the

roller itself.

110-120v Single Station Control — 3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches auto-

matically stop screen when fully down or fully up.

110-120v Multiple Station Control —Switches are similar in appearance to

110-120v Single Station Control. Screen stops when switch is released and

may be restarted in either direction. Factory adjusted limit switches stop

screen automatically when fully up or fully down.

24v Control — Three-button up-stop-down switches stop at any point

desired, operate in any sequence. Factory adjusted limit switches automati-

cally stop screen when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are option-

ally available with this unit.

➀

The key-operated power supply switch controls power to the screen and

switches. When it is "off ", the switches will not operate screen. Key may

be removed from the switch in either "on" or "off " position.

➁

A three-position key switch permits the screen to be operated directly by

key. In this case, the screen's operator must always have a key.

Screen has been factory set and should not normally require further adjust-

ment. However, if you desire to change the "up" and "down" stopping posi-

tions, proceed as follows:

CAUTION: Be sure all switches are in "off " position before adjusting limit

switches. Always be prepared to shut screen off manually when new adjust-

ment is being tested. Screen may be severely damaged if viewing surface is

allowed to run too far up or too far down.

Adjusting "fully up" position — "Up" stopping position may be adjusted by

turning the yellow limit switch adjustment socket. The yellow socket is lo-

cated on left end of screen roller and is accessible to a screwdriver/Allen

wrench (4mm or

"). Turning the socket counterclockwise will allow the

viewing surface to retract farther into the case. Turning it clockwise will cause

the surface to stop farther out of the case. One full revolution of the socket

will alter the stopping position of the viewing surface by approximately 1½".

Adjusting "fully down" position — "Down" stopping position may be

adjusted by turning the white limit switch adjustment socket. The white

socket is located on the left end of screen roller and is accessible to a

screwdriver/Allen wrench (4mm or

will allow the viewing surface to run farther down. Turning it clockwise will

shorten the viewing surface, causing it to stop in a less extended position. At

no time should viewing surface be unrolled enough to expose any part of

screen roller.

Printed in U.S.A.

Electrical Connections

Operation

Adjustments

"). Turning the socket counterclockwise

If you encounter any difficulties installing or servicing

your Targa screen, call your dealer or Draper Inc.,

Spiceland, Indiana, (765) 987-7999.