Draper Ultimate Access XL V Instructions Installation & Operation - Page 2

Browse online or download pdf Instructions Installation & Operation for Projection Screen Draper Ultimate Access XL V. Draper Ultimate Access XL V 7 pages. 220v electric projection screen
Also for Draper Ultimate Access XL V: Instructions Manual (7 pages)

Draper Ultimate Access XL V Instructions Installation & Operation
Ultimate Access E and V 220V

Section 1 - Removing Shipping Brackets

CAUTION: DO NOT remove shipping
brackets until product has been
mounted and connected to power
.
Section 4 in this document.)
Also, DO NOT OPERATE SCREEN
BEFORE REMOVING SHIPPING
BRACKETS FROM SCREEN CASE.

PLEASE READ - Safety Information

Important Safety Information
Improper installation and use of the Ultimate Access Projection Screen can result in serious injury or death. Primarily, injuries can occur if the unit
falls due to imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure.
Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and
could result in serious injury.
2. Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional. In particular, electrical
work and wiring [indicated in diagram by dashed lines] must be completed
only by a qualified professional electrician who has read this manual
completely and is familiar with the construction and operation of this
equipment and the hazards involved.
3. Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner's and installer's
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used
for mounting.
5. All hardware must be installed level. Unit must be level and square.
6. Never leave the area while operating the unit during installation, maintenance,
or normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path
of unit to be sure no persons or objects are in the area.
(especially underneath)
1. Look for any job site conditions that could interfere with installation or
operation of the system.
2. Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to serve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper,
Inc., is not responsible for improper installation, application, testing, or
workmanship related to the product at place of installation. Please retain all
instructions for future use.

(Tab-Tensioned, "V" Surfaces only)

(see
1
Remove
fasteners from
bracket clamps.
WARNING
Before Beginning Installation
Important Safety Information
8. Turn off power and any nearby equipment or cables carrying electricity
before connecting switches, wires, controls, or electrical components.
9. Do not wire motors in parallel without written permission from Draper, Inc.
10. During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
11. After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.
12. Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.
13. The safety features of the unit should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.
14. Unit may need to comply with local, state, or district rules and regulations,
in particular when installed in schools. All applicable rules and regulations
should be reviewed before installation and use.
15. Failure to precisely follow installation guidelines invalidates all
warranties.
16. Custom products/installations may not be reflected in this manual. Call
Draper, Inc., if you have questions about the installation of custom products
or any questions about your installation.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.
6. If you have any difficulties with installing, servicing, or operating your unit,
call your dealer or Draper, Inc., 765-987-7999.
page 2 of 7
2
Run screen
DOWN to expose
dowel screws.
3
Loosen screws
and remove
shipping bracket.
4
Retighten
dowel endcap
screws.