Dual Roller Coupled Motorized FlexShade
Section 1 - Mounting Brackets
Please Note: Installer is responsible for selecting
mounting hardware appropriate for site conditions.
1. Mark wall, jamb, or ceiling for placement of
mounting brackets.
2. Drill small starter hole
(if necessary)
surface.
3. Mount brackets using appropriate fasteners for
surface.
4. Place operator
end of rear shade into its
(motor)
bracket.
5. Secure motor plate with the provided clips.
6. Slide notched pin into idler bracket. Secure with
retainer clip and lock into place with rotating idler
lock.
7. Repeat with front shade.
Section 2 - Idler-End and Operator End Assemblies
Please Note: The operator will already be installed in the operator-end roller; the sliding pin idler will also be installed in the idler-end roller. It is only necessary to
install the coupler assemblies.
Caution:
• Ensure the locking ring on the idler-end coupler assembly
is fully tightened before installing roller into brackets.
There should be no play in the locking ring. If the locking
ring is loose, then the idler is in "height adjustment" mode.
Section 1.1 - 2"
Idler-End Assembly
(51 mm)
Please Note: Notches in the tube need to be lined up with the "keys" on
the couplers.
1. Insert coupler assembly into roller. Ensure the notch in the tube is lined
up with the "key" on the coupler, and press until the assembly is fully
seated in the roller.
Section 1.2 - 2"
Operator-End Assembly
(51 mm)
Please Note: Operator-end coupler assemblies will not slide straight in
to the roller tube.
1. Insert assembly into roller, with "key" slightly off-center from notch.
2. Once assembly is far enough in that the ribs are past the end of
the notch, rotate the coupler until the notch is lined up with the
"key" on the coupler.
Please Note: If the assembly will not fully seat in the roller, retract the
shaft
and tap the assembly with a rubber mallet. Do not
(if applicable)
damage the coupler.
Figure 2-A
Please Note: Ensure that retractable shaft points toward the opposite end
of the motor and remains oriented in that direction.
in mounting
Figure 1
• Wear a heavy glove on the hand
used to grip the locking ring.
®
(Extra Large Hardware)
OPERATOR
IDLER
END
END
• Tighten the locking ring until it is fully locked and it
cannot rotate any further. Ensure it is tight and will
not work loose. If locking ring cannot be tightened by
hand, use a flat screwdriver or other tool to assist.
Section 1.3 - 3"
(76 mm)
Please Note: Ensure that retractable shaft points toward the opposite
end of the motor and remains oriented in that direction.
1. Insert coupler assembly adapter into roller. Making sure the notch in
the adapter is lined up with the notch in the coupler, press until the
adapter is fully seated in the roller.
2. Insert coupler assembly into adapter. Making sure the notch in the
inside of the adapter is lined up with the "key" on the coupler, press
until the assembly is fully seated.
Section 1.3 - 3"
(76 mm)
1. Follow the same steps used for the idler-end.
Please Note: If the assembly will not fully seat in the roller, retract the
shaft
and tap the assembly with a rubber mallet. Be careful
(if applicable)
not to damage the coupler.
Figure 2-B
Operator End Coupler
C103.069
AND
C177.062SA
Please Note: Ensure that retractable shaft points toward the opposite end
of the motor and remains oriented in that direction.
page 3 of 12
RETAINER
CLIP
RETAINER
CLIP
Idler-End Assembly
Operator-End Assembly
Idler End Coupler
C103.069
AND
C177.061SA
Print Page