Draper FlexShade SkyLight 3 Installation Instructions Manual - Page 5

Browse online or download pdf Installation Instructions Manual for Indoor Furnishing Draper FlexShade SkyLight 3. Draper FlexShade SkyLight 3 6 pages.

Print Page

SkyLight 3 Installation Instructions

Installing Relieving Roller(s)

For larger SkyLight 3 FlexShades, up to two (2) Relieving Rollers may be required

to eliminate sag in the fabric. To install these Relieving Rollers:

(1) Locate the sliding Relieving Roller Anchors that were inserted in the Side

Channels (see Installing End Pulley Brackets: Part One - Step (1) and

align them with the lowest point of sag in the fabric.

(2) Insert one end of the Roller into one of the Anchors at a slight angle

(see fig. 14).

(3) Insert the other end of the Roller into the opposite Anchor and align parallel

to the Roller Fabric Assembly. Make sure the Draw Cables are set in the

channels provided at each end of the Roller.

(4) Slide the Relieving Roller into position and fix into place with the provided

self-tapping screws.

Attaching Trim Pieces

Part One: Side Channel Trim

The Side Channel Trim extends along the entire length of the Side Channels.

(1) Snap the Trim Piece into the Side Channel. You may need to tap them with a

mallet to secure them properly. Make sure that it is flush with the End Pulley

Bracket and allows plenty of room for the Tensioning Pulley and Draw

Cables to move unobstructed.

(2) Secure Trim in place with provided self-tapping screws in the pre-drilled

mounting holes. These holes will line up with the Side Channel Mounting

Holes.

(3) Repeat on the opposite side.

Part Two: End Pulley Bracket Fascia

(1) Attach the End Pulley Bracket Trim to the skylight frame, through the

pre-drilled holes, using appropriate hardware (by others).

The SkyLight 3 FlexShade is now properly installed.

Figure (14)

www.draperinc.com

Electrical Connections

Shade operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring

complete and control switch(es) fully boxed, and standardly supplied with a 6' cable

lead. Longer lead can be substituted by removing two screws in motor end of roller,

removing lead, plugging new lead in, and replacing screws. Wire to connect shade to

switch(es) and switch(es) to power supply should be furnished by installer. Connec-

tions should be made in accordance with attached wiring diagram, and wiring should

comply with national and local electrical codes.

DO NOT wire motors in parallel without written permission from Draper.

All operating switches should be "off" before power is connected.

Please Note: For low voltage wiring requirements, Draper recommends consulting

with a professional low voltage electrical contractor. It is very important that shielded

and stranded CAT 5 cable be used to prevent any electrical interference

Limit Adjustments

1 Connect the ILT switch to the motor via the terminal blocks, or via the modular

port using four conductor modular cable. When using modular cable, the cable

connectors MUST NOT be crimped in reverse, as with standard telephone cable.

2 Set the slide switch to the lower position. Press and hold the DOWN button on

the switch to move the shade to the desired lower limit. If the shade moves in

the opposite direction, release the DOWN button and depress the STOP button.

This will reverse the operation of the UP and DOWN switches.

3 Set the slide switch to the higher position. Move the shade to the desired upper

limit by pressing and holding the UP button on the wall switch.

4 Return the slide switch to the center position to return to normal operation.

5 To set the shade to an alternate format position, move the shade to the desired

position and press the STOP button. Press and hold STOP for at least three

seconds to record the position.

To Motor

with

Built-In

Low Voltage

Slide

Switch

To Motor

with

Built-In

Low Voltage

Back View

Please Note: Pressing and releasing the UP button on the switch will move the

POSITION

FUNCTION

shade to its upper limit. Pressing and releasing the DOWN button will move the

Set LOWER limit

DOWN

shade to its lower limit.

Set UPPER limit

While the motor is in motion, pressing STOP for less than two seconds will stop

Normal Operation

the viewing surface at its present position.

CENTER

Once the motor is stopped, pressing the STOP button will move the shade to its

alternate format position.

Pressing and holding the STOP button, when the motor is at rest or in motion,

for at least three seconds will record a new alternate format position.

(765) 987-7999

Please Note: 5V DC must be

connected to be able to set

limits using the wall switch.