Draper Spring-Roller Window Shade Installation And Operating Instructions - Page 2

Browse online or download pdf Installation And Operating Instructions for Indoor Furnishing Draper Spring-Roller Window Shade. Draper Spring-Roller Window Shade 2 pages.

Print Page
Spring Roller FlexShades by Draper
Pocket Headbox (Large)
STEP 1
Pocket Headbox (Small)
Secure closure
panel to endcap
with screw
Figure 6 (continued from page 1)
Field Adjustments
Each Draper Solar Control Shade is tested to ensure proper operation. Even
with this testing, some field adjustments may be needed for telescoping. If the
shade is telescoping, place a piece of high quality gaffer tape about 1" wide on the
exposed roller (where the fabric will cover it) on the side that you want the fabric
drawn toward. For example: if the fabric is tracking to the left, place the tape on the
right side.

Cleaning and Maintenance

Window covering products manufactured by Draper, when properly installed,
should require no operational maintenance or lubrication.
Most of Draper's standard fabrics may be cleaned at the window by vacuuming
with a soft brush attachment. They may also be cleaned by using a sponge or soft
cloth and mild solution of warm soapy water. A dishwashing liquid, such as Ivory
liquid, is recommended. A clean dry cloth is recommended for the metal finish.
Exceptions are Flocké and Roc-Rol fabrics, which must be cleaned with a
dry art sponge.

Troubleshooting

Roller loose in brackets:
If shade roller is loose in brackets (roller should have about
doesn't readily roll up shade, unroll shade and remove from brackets. Re-roll the
cloth by hand and replace it in brackets.
Roller too tight:
If shade roller is wound too tight, shade will not fully or freely unroll. Remove rolled
up shade from brackets, partially unroll cloth by hand, and replace in brackets.
Spring Tensioning Instructions
1 Clamp the flat spear on the left end of the roller securely (a pair of vise-
grip locking pliers works well) and rotate clockwise 15 turns. Take care
not to allow the pliers to slip as tension increases.
2 Once the desired amount of rotations have been added, stop the rotation
of the slotted end in a vertical position. The vertical position must be
maintained to lock the mechanism.
3 Release a small amount of pressure off the roller and allow it to rotate very
slowly (less than 180 degrees of rotation will be necessary). This will allow
the spring mechanism to lock into position.
STEP 2
STEP 3
/
" end play) and
1
8
www.draperinc.com
WINDOW SHADE
WINDOW SHADE
F
1
Cloth Width (CM)
Outside Measurement (OM)
WINDOW OPENING
(IM) = Outside Measurement (OM) with 1/8" deduction.
Headbox with Endcaps*
Small
Large
A¹
3
15
/
"
4
11
/
16
B¹
N/A
N/A
C¹
1
/
"
1
/
11
5
16
D¹
1
/
"
1
/
9
11
16
E¹
3
7
/
"
4
11
/
16
*For fascia, subtract
**Please Note: When mounting brackets to the wall, use
the hole closest to the wall. When mounting brackets to
the ceiling, use the hole furthest away from the ceiling.
(765) 987-7999
Page 2 of 2
A
Brackets**
Small
Large
"
A²
7
/
"
1
15
/
"
16
8
16
B²
/
"
1
/
"
5
3
8
16
"
C²
1¼"
1
/
"
5
8
8
"
D²
1
/
"
2
/
"
5
3
16
8
16
"
E²
1
15
/
"
2
11
/
"
16
16
16
/
"
1
16
1
E
1
C
1
1
D
2
E
2
B
2
D
2
A
2
C