Bosch WLM24441BY Instruction Manual - Page 2

Browse online or download pdf Instruction Manual for Washer Bosch WLM24441BY. Bosch WLM24441BY 10 pages.

Print Page
Safety instructions
Important
information
– Read and follow the operating and installation instructions and all other information enclosed
with the washing machine.
Preparing/Protecting the laundry and the machine
– Retain documents for subsequent use.
– Empty pockets.
Risk of electric shock
– Never pull out the mains plug by tugging the power cord.
– Look out for metal items (paperclips, etc.).
– Never insert/pull out the mains plug with damp hands.
– Wash delicates in a net/bag (tights, curtains, underwired bras).
Risk of death
For worn-out appliances:
– Fasten zips, do up any buttons.
– Pull out the mains plug.
– Brush sand out of pockets and collars.
– Sever the power cord and discard together with the plug.
– Destroy the lock on the washing machine door.
– Remove curtain fittings or in a laundry bag.
This will prevent children from locking themselves and risking their
lives.
Before washing for the first time
Risk of suffocation
– Keep packaging, plastic film and packaging parts out of the reach of
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment
children.
II:
Risk of poisioning
– Keep detergents and care products out of the reach of children.
– approx. 1 litre water
Risk of explosion
– Items of laundry pretreated with cleaning agents containing solvents,
– detergent (dosage according to the manufacturer's instructions for light soiling and the
e.g. stain remover/cleaning solvents may lead to an explosion after
appropriate degree of water hardness)
being loaded into the washing machine.
Set the programme selector to Easy-Care
Rinse items of laundry thoroughly by hand beforehand.
the programme, turn the programme selector to
Risk of injury
– Washing machine door may become very hot.
– Take care when draining hot detergent solution.
– Do not climb onto the washing machine.
Laundry with different degrees of soiling
– Do not lean on the open washing machine door.
– Do not touch the drum in case it is still spinning.
Wash new items separately.
– Be careful when opening the detergent drawer while the machine is
Light
Do not prewash.
in operation.
If required, pretreat stains. Select
Heavy
Load less laundry. Prewash.
If required, pretreat stains. Select
Consumption values
Soaking
Load laundry of the same colour
Additional
Electricity
Programme
***
Pour soaking agent/detergent into dispenser II according to the manufcturer's instructions.
Programme
Load
Water
function
consumption
***
duration
***
Set Cottons
30 °C programme and select Start/Pause
select Start/Pause
. After the required soaking time, reselect Start/Pause
Cottons
30 °C
—-
6.0 kg
0.29 kWh
57 l
1:33 h
programme is to be continued or change the programme.
Cottons
30 °C*
Intensive
6.0 kg
0.31 kWh
57 l
2:03 h
Cottons
40 °C
—-
6.0 kg
0.50 kWh
57 l
1:38 h
Starching
Laundry must not be treated with fabric softener
Cottons
40 °C*
Intensive
6.0 kg
0.52 kWh
57 l
2:03 h
Starching is possible in all washing programmes if liquid starch is used. Add starch to the
Cottons
60 °C
—-
6.0 kg
0.85 kWh
57 l
1:43 h
fabric softener dispenser
Cottons
60 °C*
Intensive
6.0 kg
0.89 kWh
57 l
2:03 h
Cottons
90 °C
—-
6.0 kg
1.81 kWh
66 l
1:58 h
Dyeing/bleaching
Easy-Care
40 °C
—-
3.5 kg
0.45 kWh
54 l
1:00 h
Dye in small quantities only. Salt can corrode stainless steel.
Easy-Care
40 °C*
Intensive
3.5 kg
0.49 kWh
54 l
1:20 h
Observe the dye manufacturer's instructions.
Do not bleach laundry in the washing machine.
Mix
40 °C
—-
3.5 kg
0.53 kWh
50 l
1:03 h
Delicate/Silk
30 °C
—-
2.0 kg
0.18 kWh
26 l
0:39 h
Wool
30 °C
—-
2.0 kg
0.14 kWh
40 l
0:36 h
* Programme setting for testing according to the currently valid version of EN60456.
Note for comparative testing: for testing the test programmes, wash the specified load using the maximum spin speed.
Programme
Additional
Load
Annual energy
Annual water consumption
consumption
function
Cottons Eco
40/60°C
Intensive**
6/3 kg
196 kWh
8650 l
** Programme setting for testing and energy labelling in accordance with directive 2010/30/EU and cold water (15°C).
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient
temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected
Downloaded From WashingMachine-Manual.com Manuals
additional functions.
8
– Risk of electric shock!
Care
Pull out the mains plug!
– Risk of explosion! No solvents!
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent residues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residues.
1. Pull out the drawer up to the stop position, press down the latch on the
insert and remove the drawer completely .
60 °C and select Start/Pause
. At the end of
2. Remove insert: pull insert upwards with finger.
Off.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure in place (the cylinder should fit over the
guide pin).
5. Insert the detergent drawer.
(Intensive) additional function.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
(Intensive) additional function.
Leave the washing machine door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool.
Descaling
No laundry in the machine!
. After approx. 10 minutes,
This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the
if the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
page 13
Information on the display
in accordance with the manufacturer's instructions.
Please close the door immediately because of rising water level. In pause
status
and
are displayed alternately.
Door is locked due to safety reasons (water level and/or temperature are too
high); in pause status,
and
are displayed alternately. If you need
to open the door, wait for the temperature to drop or drain the water (e.g. select
Empty
programme).
Door cannot be locked/unlocked due to high temperature of the door lock.
Wait a moment and try again.
Flashing (no water supply):
On (low water pressure):
Tap turned on?
Only information. No influence
Inlet filter blocked ? Clean filter.
page 11
on the programme process.
Supply hose kinked or blocked ?
Clean drain pump;
page 11
outlet pipe/drainage hose blocked.
Switch off the appliance, wait 5 seconds and switch it back on.
other displays
If the display appears again, call the customer service
9
– Risk of scalding!
What to do if ...
Maintenance
Allow detergent solution to cool down!
– Turn off the tap!
Water is leaking out.
Drain pump
– Set the programme selector to
Off, disconnect the mains plug.
No water supply.
Detergent not dispensed.
1. Open and remove the service flap.
Washing machine door cannot be
2. Release the drainage hose from the clip.
opened.
Remove the sealing plug from the drainage hose, allow the detergent
solution to flow out. Push the sealing cap back in.
Programme does not start.
Detergent solution is not drained. – Clean the drain pump.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff from
inside and clean the pump. (impeller in the pump must be able to rotate).
Water not visible in the drum.
Spin result not satisfactory.
4. Clean any residual lye or fluff from the thread of the pump cap and
pump housing.
Spin cycle performed several
5. Attach the pump cap and screw it on tight until the stop, handle is upright.
times.
Place the drainage hose back in the retainer.
Compartment
completely.
6. Place the service flap back on and close.
Odour formation in the washing
machine.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment II and start
Foam escapes from the detergent
the Empty
programme. Then select and start a new washing
drawer.
programme with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Excessive noise, vibrations and
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
"wandering" during spin cycle.
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spin
/Empty
).
3. Touch Start/Pause
button and allow the programme to run for approx. 40 seconds.
Display panel/indicator lamps do
4. Set the programme selector to
Off . Disconnect the mains plug.
not light up while the appliance is
running.
Clean the filter:
Aqua-Stop
Standard
Aqua-Secure
1. Remove the supply hose from the tap.
Programme sequence longer than
Clean the filter with a small brush.
usual.
or
Detergent residues on the laundry. – Occasionally, phosphate-free detergents contain water-
on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to
– Turn off the tap and call the customer services.
page 13
2. Reconnect the supply hose and check if it is tight.
10
11
Emergency release
e.g. in the event of power failure
– Fit/refit drainage hose correctly.
Interrupted programme will be resumed when power returns.
– Tighten the screw connection of the supply hose.
However, if the laundry has to be removed, the washing
– Start/Pause
not selected?
machine door can be opened as follows:
– Water tap not turned on?
Risk of scalding.
– Supply hose filter blocked? Clean the filter.
page 11
The detergent solution and laundry may be hot.
– Supply hose kinked or trapped?
If possible, leave it to cool down.
– Safety function active. Programme stopped?
page 4
Do not reach into the drum if it is still rotating.
–
(Rinse stop = no final spin) selected?
page 6
Do not open the washing machine door if water can be seen
– Can be opened by emergency release only.
page13
through the glass.
– Start/Pause
or
Finish-in time selected?
– Set the programme selector to Off and disconnect the mains plug.
– Washing machine door closed?
– Drain the detergent solution.
page 11
– Pull the emergency release with a tool and release. The washing
– Clean waste pipe and/or drainage hose.
machine door can then be opened.
– Not a fault - water below the visible area.
– Wash small and large items of laundry together.
–
Easy iron selected?
page 6
– Speed selected too low?
page 6
Customer service
– Not a fault - unbalanced load detection system adjusts
the imbalance.
not rinsed out
– Remove the insert. Clean detergent drawer and insert.
If you cannot rectify the fault yourself
page 12: What to do if ..., please contact our after-
page 10
sales service. We will always find a suitable solution and will avoid a visit from a service
– Run the Cottons
90 °C programme without
technician wherever possible.
laundry.
The contact details for all countries can be found in the enclosed after-sales service directory.
– Use standard detergent.
– Too much detergent used?
Please give the customer service the product number (E-Nr.) and the production number
Mix 1 tablespoon of fabric softener with ½ litre of water
(FD) of the appliance.
and pour into compartment II in the detergent drawer.
You will find the identification plate containing
– Reduce detergent dosage for the next wash cycle.
this information on the frame of the open door ,
– Are the appliance feet fixed?
and of the rating plate on the back of the
Secure the appliance feet.
Installation instructions,
appliance.
Product number
Production number
page 5
– Transport bolts removed?
Rely on the professionalism of the manufacturer. Please contact us.
Remove transport bolts.
This will ensure that the repair is carried out by trained service technicians who arrive
Installation instructions, page 3
equipped with genuine spare parts for your appliance.
– Power failure/off? Interrupted programme will be
resumed when power returns.
– Circuit breaker tripped? Reset the circuit breaker/
change the fuse.
– If the fault occurs repeatedly, call the customer service.
– Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an
additional rinse cycle.
insoluble residues.
– Select Rinse
or brush the laundry after washing.
Off and pull the mains plug out of the socket.
page 13
12
page 11
Washing machine WLM20461BY
WLM24441BY
en Instruction manual
13