Bosch GDS Professional 24 Installation Instructions - Page 3
Browse online or download pdf Installation Instructions for Oven Bosch GDS Professional 24. Bosch GDS Professional 24 5 pages. 24" electric built-in single and double ovens
Also for Bosch GDS Professional 24: Original Instructions Manual (14 pages)
Print Page
Electrical requirements
!
WARNING
Electrical Shock Hazard
Electrically ground oven.
Connect ground with 10-gauge-minimum solid
copper wire.
Failure to follow these instructions could result
in death, fire or electrical shock.
If codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with local codes.
Installation Steps
Grasp oven
C
frame to lift
oven.
A
power
B
supply cable
Remove
C
shipping
feet.
Replace
C
oven door.
Preparation
A
!
WARNING
Excessive Weight Hazard
Use two or more people to move and install
oven.
Failure to follow this instruction can result in
back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front lower
corners of oven.
Do Not
remove
shipping feet.
1.
Turn power supply off. Move oven close to
final position.
• Remove and discard shipping materials, tape
and protective film from the oven. Do Not
remove shipping base or shipping feet at the
front lower corners of oven. The shipping feet
will protect the lower oven trim until oven is
inserted into cabinet.
• Remove and set aside racks and other parts
from inside oven.
Page 2
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is properly grounded.
Do Not have a fuse in the neutral or grounding
circuit.
Oven must be connected to the proper electrical
voltage and frequency as specified on the
model/serial rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.)
CONNECT WITH COPPER WIRE ONLY.
Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts) require a separate
40-ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30-ampere circuit.
Check oven
D
operation.
Remove
oven racks.
A
A
Remove
A
oven door.
2.
Completely open lower oven door. Insert
small end of a door removal pin into each door
hinge. Grasp door handle from the bottom and
gently close door as far as it will shut. Lift slightly
and grasp bottom of door with other hand. Pull
door out at bottom to remove. Set door aside on
protected surface.
Repeat for upper oven door.
Use screws to attach
C
oven to cabinet.
Grasp oven
C
frame to lift
Reattach side
C
oven.
trim.
Remove
trim screws.
Remove side
trim.
Use screws to
C
attach oven to
cabinet.
power
B
supply cable
Remove
C
shipping
feet.
Insert small
end of pin
here.
A time-delay fuse or circuit breaker is
recommended.
Connect directly to the fused disconnect (or
circuit breaker box) through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire).
Flexible armored cable from appliance should
be connected directly to junction box.
Fuse both sides of the line.
A U.L.-listed conduit connector must be
provided at the junction box.
Do Not cut the conduit.
Wire sizes and connections must conform with
the rating of the appliance and to the
requirements of the National Electrical Code,
ANSI/NFPA 70 — latest edition (*, See Page 1)
and all local codes and ordinances.
Check oven
D
operation.
Remove
A
oven racks.
Remove
A
oven racks.
Replace
C
oven doors.
3.
Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Reattach side
C
trim pieces.
Remove side
A
trim.
Remove trim
A
screws.
Remove
A
oven doors.
Remove trim screw.
Pull trim out.
Pull top of trim
down.