Alen MPF-12CR Owner's Manual - Page 15

Browse online or download pdf Owner's Manual for Portable air conditioner Alen MPF-12CR. Alen MPF-12CR 15 pages. Portable air conditioner
Also for Alen MPF-12CR: Owner's Manual (17 pages)

Print Page

COOL , HEAT , and FAN ONLY Operation

1. If the AUTO mode is not comfortable , you may manually override the settings by using COOL, DRY,

HEAT(HEAT PUMP units only), or FAN ONLY modes.

2. Push the TEMP button to set the desired room temperature. When in COOLING mode, the most

comfortable settings are 21 C/70 F or above. When in HEATING mode, the most comfortable settings

are 2 8 C/82 F or b elow.

3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW.

4. Push the ON/OFF button. The operation lamp lights and the air conditioner starts to operate per your

settings. Push the ON/OFF button again to stop this unit operation.

NOTE:

The FAN ONLY mode cannot be used to control the temperature. While in this mode, only steps 1 3 and 4 may

be performed.

DRY OPERATION

1. Push the MODE button to select DRY.

2. Push the TEMP button to set the desired temperature from 21 C/70 F to 28 C/82 F.

3. Push the ON/OFF button. The operation lamp lights and the air conditioner starts to operate in

the DRY mode. Push the ON/OFF button again to stop this unit operation.

TIMER Operation

TIMER ON button can set the auto-on time of the unit. TIMER OFF button can set the auto-off time of the unit.

1. To set the starting time.

1.1 Push the TIMER ON button, then the remote controller shows TIMER ON , the last set time for the

starting operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now ready

to reset the time to START the operation.

1.2 Push the TIMER ON button again to set desired unit start time.

1.3 After setting the TIMER ON ,there will be a one-half second delay before the remote controller transmits

the signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears

and the set temperature will re-appear on the digital display.

2. To set the stopping time.

2.1 Push the TIMER OFF button and the remote controller will show TIMER OFF, the last set time for

the stopping operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now

ready to reset the time of the STOP operation.

2.2 Push the TIMER OFF button again to set the time you want to stop the operation.

2.3 After setting the TIMER OFF ,there will be a one-half second delay before the remote controller transmits

the signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears

and the set temperature will re-appear on the digital display.

3. Set the starting & stopping time

3.1 Push the TIMER ON button, the remote controller will show TIMER ON, the last set time for START

operation and the signal "h" will be shown on the DIGITAL display area. You are now ready to readjust

the TIMER ON to start the operation.

3.2 Push the TIMER ON button again to set the time you want to start the operation.

3.3 Push the TIMER OFF button, the remote controller will show TIMER OFF, the last set time for STOP

operation and the signal "h" will be shown on the DIGITAL display area. You are now ready to reset the

time to STOP operation.

3.4 Push the TIMER OFF button again to set the time you want to stop the operation.

3.5 After setting the TIMER, there will be a one-half second delay before the remote controller transmits the

signal to the Air Conditioner. Then, after approximately another 2 seconds, the set temperature will

re-appear on the digital display .

NOTE

1. Please reset the TIMER after cancelling the former time settings.

2. The setting time is relative time. That is the time set is based on the delay of the current time.