Anchor GO GETTER Owner's Manual - Page 2
Browse online or download pdf Owner's Manual for Speakers Anchor GO GETTER. Anchor GO GETTER 9 pages. Sound system
Also for Anchor GO GETTER: Quick Start Manual (2 pages), Quick Start Manual (2 pages), Quick Start Manual (2 pages), Quick Start Manual (2 pages)
Print Page
Go Getter Sound System Owners Manual
BASIC SYSTEM OPERATION
NOTE: Fully Charge Batteries Before First Use!
1. Set all Input Level Controls to minimum
& Tones Controls to flat or the middle
setting before turning your system on
2. Plug a wired microphone into the MIC
1 or MIC 2 jacks and/or plug an audio
source into the LINE-IN jack
3. Switch POWER to ON, the BATTERY LED
will light
4. Slowly increase the Level Control for the
input jacks used to the desired volume
5. Adjust BASS & TREBLE controls to
desired sound quality
IMPORTANT: Make all connections with shielded
cables to avoid hum, buzzing or interference.
SPEAKER STAND SETUP
1. Loosen the Lower Collar Knob
2. Separate the stand legs until the leg support Cross
Braces are parallel to the floor
3. Tighten the Lower Collar Knob
4. Loosen the Upper Collar Knob and extend the
center pole
5. Adjust height and retighten the Upper Collar Knob
6. Place your Anchor sound system on the stand
UPPER
COLLAR
KNOB
LOWER
COLLAR
KNOB
CROSS BRACES
RX INDICATOR LIGHTS FOR
WIRELESS RECEIVER 1
A solid red light on one of the
RX Indicator Lights indicates
that the sound system is getting
good reception with the wireless
A solid red light on both RX
Indicator Lights indicates that
the sound system is a optimum
reception with the wireless
WIRELESS MICROPHONE 1
wireless microphone levels
WIRELESS MICROPHONE 2
LINE IN LEVEL CONTROL
LINE IN - INPUT JACKS
The 1/8" (3.5 mm) jack
input is used to hook up an
iPod, a portable CD/ MP3/
tape player, laptop com-
puter, or similar external
audio source
SPEAKER STAND ADAPTER
The 1/4" unbalanced input
can be used for other
The 1.5" diameter Speaker Stand
communication devices
Adapter lets you mount the Go
including a mixer or daisy
chaining together multiple
Getter on a speaker stand.
Go Getter speakers
1. Slide Speaker Stand Adapter
into slot on Go Getter bottom
2. Tighten screw to secure
adapter
3. Place unit on stand carefully
4. Tighten screw on Adapter
collar securing Go Getter on
stand
For System Setup & Operation Videos Visit Our Website: www.anchoraudio.com
BACK PANEL OF GG-U2 (AC/DC)
microphone
microphone
LEVEL CONTROL
Adjust knob to control
Go Getter
LEVEL CONTROL
VOLUME
VOLUME
LINE IN
VOLUME
LINE IN
LINE IN
LINE OUT
LINE OUT - OUTPUT JACK
Balanced 1/4" – provides a combined
output of all active system inputs
Record your presentation or connect to
another powered sound system
WIRELESS RECEIVERS 4
(see page 6)
RX INDICATOR LIGHTS FOR
WIRELESS RECEIVER 2
www.anchoraudio.com
SPEAKER OUT
MIC 1
MIC 2
BASS
VOLUME
VOLUME
POWER/LOW BATTERY
POWER JACK
POWER
MIC 1
MIC 2
ON
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
CHARGE INDICATOR LIGHT
WIRED MIC INPUTS
MADE IN USA
SIX YEAR WARRANTY
TONE CONTROLS - BASS/TREBLE
WIRED MIC LEVEL CONTROLS
SPEAKER OUT -
OUTPUT JACK
Connect the system to a Go
Getter unpowered companion
speaker
BATTERY LEVEL
INDICATOR LIGHT
POWER SWITCH
2