Bosch 1613EVS Instruction Manual - Page 6

Browse online or download pdf Instruction Manual for Power Tool Bosch 1613EVS. Bosch 1613EVS 28 pages. Plunge router
Also for Bosch 1613EVS: Instruction Manual (28 pages)

Print Page

• Replace damaged cords immediately. Use of

damaged cords can shock, burn or electrocute.

• If an extension

cord is necessary,

a cord with

adequate

size conductors

should

be used to

prevent

excessive

voltage

drop, loss of power

or overheating.

The table

below

shows

the

correct

size to use, depending

on cord length

and amperage

rating on the tool's nameplate.

in doubt,

use the next heavier

gauge.

Always

use U.L. and CSA listed extension

cords.

Ampere Rating

(shown on nameplate)

2.1-

3.5-

5.t-

7.1-

12.1-

2.0

3.4

5.0

7.0

12.0

16.0

25'

50'

-_ 75'

100'

L) 150'

Wire Gauge

Note:

The smaller the gauge number, the larger

the wire is in the cord.

"SAVE THESE INSTRUCTIONS"

Variable

Speed

with Dial Setting

(1613EVS

& 1614EVS)

Your router is also equipped with a variable

speed dial 2. The router bit speed can be preset

from 12,000 to maximum nameplate RPM by

rotating the dial to the desired setting. The dial

may be set on or between any of six positions (1

= low through 6 = high).

The "Lock-ON"

button may also be used with any setting of the

dial.

The following

speeds generally

apply, but pre-

cise

settings

are

largely

determined

experience

with the material

being

cut.

Mo-

mentary speed variation

is normal when starting

the router until the electronic

regulator

takes

control.

Dial

1613EVS

1614EVS

RPM

Material

12,000

nonferrous

metals,

14,000

14,500

larger

diameter

router

16,000

17,000

bits and cutters.

18,000

19,500

Softwoods,

plastics,

20,000

22,000

counter

tops,

smaller

22,000

23,000

diameter

router

bits

and cutters.

"Soft Start" Feature

(1613EVS

& 1614EVS

)

The router is equipped with the "soft start"

feature which gradually increases the starting

speed and torque, reducing the stress that oc-

curs from a high torque start.

Trigger

Switch

with

"Lock-ON"button

Your

tool can be turned "ON"

or "OFF"

squeezing

or releasing

the trigger.

Your tool is

also equipped

with "Lock-ON"

button,

located

on the left side of the trigger handle, that allows

for continuous

operation

without

holding

the

trigger.

TO LOCK SWITCH "ON": Squeeze trigger,

depress button and release trigger.

TO UNLOCK

THE SWITCH:

Squeeze

trigger

and release

it without

depressing

the "Lock-

ON" button.

WARNING!

If the "Lock-ON"

button is con-

tinuously

being

depressed,

the trigger

cannot

be released.

Start the tool before

applying

to work

and let

the tool come to full speed before

contacting

the workpiece.

Lift the tool from

the work

before releasing

the switch.

DO NOT turn the

switch "ON" and "OFF"

while the tool is under

load; this will greatly

decrease

the switch life.

Router Bit Installation

and Removal

WARNING!

Always disconnect the tool

from the power supply before installing router

bits, accessories or making any adjustments.

Installing

a Router

Bit

Turn the armature

shaft to align the flats with

the spindle

lock 11, and press the spindle

lock

firmly down to engage it. Next, use the wrench

supplied

to loosen

the collet chuck

assembly.

Insert the shank of the router bit into the collet

chuck as far as it will go, then back the shank