Electrolux EIDW6405HT - Fully Integrated Dishwasher Installation Instructions - Page 2

Browse online or download pdf Installation Instructions for Dishwasher Electrolux EIDW6405HT - Fully Integrated Dishwasher. Electrolux EIDW6405HT - Fully Integrated Dishwasher 2 pages. Installation instructions
Also for Electrolux EIDW6405HT - Fully Integrated Dishwasher: Installation Instructions (2 pages), Specifications (2 pages), Installation Instructions (2 pages)

Print Page

Measure

height of cabinetopening

from underside

countertop

tofloor.

Check chartfor

height opening

and

suggested

adjustment.

Leg Leveler

Adjustment

Chart

Heightof

Number of Tumsto

Cabinet Opening

Adjust Levelers

34"(86.4cm)

34 _8"(86.7cm)

34 _"

(87.2cm)

34_z"(87.6cm)

Move dishwasher

to front of installation

area.

Loosen the rear ]evefing legs by turning counterclockwise.

Refer

to chart for number

of turns.

Dishwasher

Anchoring

instal] the Cabinet

Seal Kit (Instn.lctions

included in Kit)

Choose

one of the methods

of attachment

below to secure unib

holes need to be pre-ddlled

using a #5 ddll bit regardless

the option chosen:

a. Side Mount Cabinet

Clips (Preferred

Method of

attachment)

b. Top Mount Cabinet

Clips (to be used when Side Mount

is not an available

option)

CAUTION:

Use extreme

care in mounting

the dishwasher

as to

not scratch,

bump or otherwise

damage

the console

or tub.

To install

the Side Mounting

Clips,

Depending

on space allowed

in cabinet the Side Mounting

Clips can be installed

with the holes for the screw Lip (preferred

method)

or down as shown in the illustrations

below.

(Use extreme

caution when the dips are in the down position while installing

the dishwasher).

NOTE: Install

Side Mount Brackets before

unit is installed

into

the cabinet.

Insert screws

intothe

front

holes

of the

mounting

clips only. (See image

below)

Use

{f measures

341/_ '' to

35"

Use if measu,_s 34" to 34V_"

TO install

using

Top Mou nt Cabinet

Clips:

Depending

on the

depth of cabineb the Top Mount

Clip have a break off point

that can be removed if necessary.

NOTE:

Install

Top Mount Clips before

unit is installed

into

the cabinet.

Screw clips flrrnly

to top brace using

screws

provided

in the literature

pack. (See image

below)

If levelers

need to be removed,

make sure that the floor is free of all

obstr_lcfions.

Care fully place dishwasher

inside cabinet area such that is

centered

in opening.

Use caution when moving dishwasher

prevent damage to cabinet, dishwasher

and floor.

Front of door needs to be even with the front of adjoining

cabinets.

Front levelers

ShOLddallow 5/16" below underside

of countertop

to top of console.

9. Check that dishwasher

is level from side to side by placing

a level

against the top front section

of the tub.

See Figure

6a.

10. Check that the dishwasher

is level from front to back by taking

out the lower rack, place level on the lower rack wheel support

the bottom of the tub. See Figure

6b.

11. Adjust levelers

Lip or down until dishwasher

is level.

Holes need to be pre-drified

using a #5 drill to secure

unit.

12. Screw mounting

brackets firmly to cabinet

using screws provided

in literature

packet. See Image

Below.

Figztre

Figttre

13. Open and close dishwasher

door slowly. Ensure that there is

clearance

to the console.

Adjust

accordingly

unfil door opens

and closes freely.

Property

Damage

Do not solder

within

6" of the water inlet valve. Damage

the plastic

parts

in the valve may occur.

Use care that

no sealer,

dirt,

or other objects

enter the valve.

Damage

to the filter

screen

may occur.

Be sure the dishwasher

is placed

where the water

inlet

valve will be kept

from freezing.

If the valve

freezes,

it may

rupture

and flooding

may occur.

Water Line

FlUsh water line before connecting

it towater

inlet valve to

prevent early clogging of filter screen. Place a bunched

towel

over end of line to prevent splashing.

Open water supply valve for

a few seconds and let water

drain into a pan.

Turn off water

supply at shut-off

valve.

Rot.de water

line to water

inlet valve as shown in Figure

While firmly

pulling water supply line into 90 ° elbow, tightly

connect water

supply to water inlel valve. Supply line must be

free of kinks, scales,

chips, and lubricants.

Turn on water supply and check for leaks.

Electrical

Supply

Remove junction

box cover and pui] house widng into junction

box. See Figure

7a.

Use a UL listed conduit connector

(not included)

at box to

stabilize wiring.

Connect incoming

black lead to dishwasher's

black lead,

incoming white lead to dishwasher's

white lead and incoming

green lead to dishwasher's

green lead with wire nuts. (See

Grounding

Instruction

Warning).

Wire nuts must be tight.

Replace junction

box cover.

Box

White

Wire

Junction

Wire

to White

Wire

Box Cover

to Black

Wire

(Neutral)

Figm'e

(Hot)

Figure

71)

check these items:

Water and electrical

lines are straight out in front of the

dishwasher.

All four leg levelers

are positioned

properly.

Cabinet

Seals are positioned

on the sides and top of the

dishwasher.

Cabinet

Attachment

Clips are attached to the cabinet on

both comers on top of the dishwasher.

Replace

Toe and Kickplate.

Note:

When

replacing

Toe

and Kickplate

hand tighten

screws.

Electric

Shock

Hazard

Grounding

Instructions:

The dishwasher

must

be connected

to a grounded

metal,

permanent

wiring

system

or an equipment-grounding

conductor

must

be run with the circuit

conductors

and

connected

to the appliance's

equipment

grounding

terminal

or lead.

]t is the consumer's

responsibility

to contact

qualified

installer

to make

sure

the electrical

installation

conforms

with the National

Electrical

Code and

local codes

and ordinances.

Do not connect

the dishwasher

to the power

supply

until the

appliance

is permanently

grounded.

All wiring

connections

must

be enclosed

in the junction

box.

This unit

has copper

lead wires.

Joining

aluminum

building

wire to stranded

copper

wire

should

be done by a qualified

electrician

using

materials

recognized

by UL and local codes.

Do not use an extension

cord. Such use can result

in fire,

electrical

shock,

or other personal

injury.

Failure

to follow

these

instructions

could

res ult in death or

serious

injury.

Review Figures

8, 9 and 10 to see the different ways to connect

dishwasher

to drain system.

Choose

method

that best suits

yourneed.

Sink at R_h,

Sink ,t L_#

F_.re

The drain

hose h)op mu_t be at least

32" high

[rom the [Ioor

to insuraproper

draimtga,

If you connect

to a sink drain, entry will need to be above trap.

A "Y" branch tailpiece

and connector

kit, not included,

will make

this method easier and includes

all needed fillings

and

instructions.

See Figure

If you connect

to a sink trap, local codes may require

you to

install an air gap kit, (not included). The drain hose will be routed

from dishwasher

to air gap inlet as shown

in Fig ure 9. An air

gap kit is available

from a plumbing

supply store.

(If the drain

hose is installed

through

the floor, an air gap is necessary).

If you connect

to a disposer,

the large end of drain hose will fit.

Fig ure 10(a).

The knock

out plug

must

be removed

from

inside

disposer

inlet before

making

the final

fit to drain

hose

See Figure

10(b).

Figttre

lOpO

Cuth_t 3/4"_,mne_tion,

Sink at Le#

"_a_a_tit

Gap

' "

109(b)

The drain

hose

h)op mu_t be at h,a_t 32"

high [rom

the [loor

to insm'e proper

_'ainag_

[fthe cabinet wall is wood,

sand edges of hole until smooth and

rounded.

If cabinet wall is metal, cover all sharp edges with

eleclrical

or duct tape to avoid

cutting drain hose.

Move unit back in place while routing drain hose through

access

hole. Use caution to prevent damage to the dishwasher,

floor and

cabinets.

IMPORTANT:

Make sure

there are no sharp

bends

or kinks that

might

restrict

drain

flow.

Secure

drain hose to sink drain, disposer, or separate

trap with a

clamp.

IMPORTANT:

Be careful not to overtighten

clamp or

you may damage

end of hose.

Do not connect

hose to

horizontal

pipe between

sink drain and disposer.

Be sure unit does not rest on drain hose.

I_should

be free of

electrical

components

and door spnngs. Do not cut corrugated

drain hose.

PLdl excess

through

cabinet and place under sink.

Make

sure hose does not come

in contact with any sharp edges.

Electric

Shock

Hazard

Disconnect

electrical

power

at the fuse

box

or circuit breaker

box before

beginning

installation.

Failure

to follow

this warning

could

result

death or serious

injury.

Failure

this

warning

may

result

injury.

check

these items:

Water and drain lines have no kinks and move freely

behindthe

dishwasher.

Water

supply is turned on.

Joints are free of leaks.

Wiring connections

to junction

box are tight all access

panels

are secured

back in place.

Replace

kickplate.

See Figure

Drain hose is assembled

to Drain Hose Connector.

All packing materials

and consumer

literature

have

been removed

from inside unit.

Dishwasher

is level and securely fastened.

Open and dose door to make sure it does not hit

surrounding

cabinet or countertop.

Make sure that all wire ties are removed

from the Adjustable

Rack Assembly,

Versa Tray, Utility Tray and Silverware

Baskets.

Operate

the machine

through

least one fill and pump-out,

checking

the following

items:

On EIDW6405HT

press and hold SANITIZE

keypad for 8

seconds before first use.

At first fill, approximately

2 minLdes, make

sure water

completely

covers filter surface.

At pump-ouh

(pump_ut

is either when the cycle is

completed

or canceled,

refer to the Use and Care Guide

for Stad/Cancel),

make

sure all water

is pumped

ouk

Check water connections

again for leaks.