AIRTAC DPSP1-01 Quick Start Manual

Browse online or download pdf Quick Start Manual for Switch AIRTAC DPSP1-01. AIRTAC DPSP1-01 2 pages. Digital display pressure switch

Print Page

DPS Series

Digital Display Pressure Switch

Precautions

Do not drop 、 knock or apply excessive impact while handling.Otherwise

could cause damage and a malfunction.

The tensile strength of the cord is 60N.Applying a greater pulling

force on it can cause a malfunction.

Do not exceed the screw-in torque of 7N m when installing piping.

Exceeding this value may cause malfunctioning of the sensor.

Do not use it with corrosive and/or flammable gases or liquids.

Please use it within rated pressure range.

Turn off the power before connecting the wires.

Don't use in an environment with spattering liquid of oil or solvent.

Separate power lines from high voltage lines,avoiding wiring in the

same conduit with these lines.

Specifications

Model

DPSN1-01、DPSN1-10、DPSP1-01、DPSP1-10

12 to 24VDC ±10%,Ripple(p-p)≤10%

Voltage

Input power

Current

45 mA or less

consumption

fluid type

Non-corrosive gas

DPSN1(P1)-01:-100kPa to 100kPa

Measurement

range

DPSN1(P1)-10:-100kPa to 1000kPa

DPSN1(P1)-01:200kPa

Pressure

Withstand

range

pressure

DPSN1(P1)-10:1500kPa

Measurement

±2% F.S. ±1 digit

error

Repeative

±0.2% F.S.

accuracy

Temperature

±3% F.S.(Base 25℃,Range 0 to 50℃ )

error

Display

Double row LCD display

Type

4-digit measurement, 3.5-digit setting

Display

Output

Color

2-color LCD (Red/Green)

Display

100ms、250ms、500ms、1000ms

period

DPSN1:Built-in two sets of NPN output

Output group

DPSP1:Built-in two sets of PNP output

NPN:Maximum applied voltage 30V/100mA,

Transistor

Retained voltage <1.5V

output

PNP:Maximum applied voltage 30V/100mA,

Switch output

Retained voltage <1.5V

2ms、20ms、50ms、100ms、250ms、500ms、

Response time

1000ms、2500ms、5000ms

DPSN1(P1)-01:0.1、0.2、0.3

Hysteresis

DPSN1(P1)-10:1、2、3

8(kPa)

...

Basic mode, Hysteresis mode, Window

Output mode

comparator mode

DPSN1(P1)-01:kPa、kgf/cm 、bar、psi、mmHg、inHg

Pressure Unit

DPSN1(P1)-10:MPa、kPa、kgf/cm 、bar、psi、cmHg、inHg

Vibration

10 to 500Hz with 10mm Amplitude in X, Y, Z directions

resistance

for 2hrs

Impact

Maximum 100m/s , X, Y, Z directions 3 times each

resistance

Operating

0℃ to +50℃

Temp. range

Stored

-20℃ to +65℃

Temp. range

Humidity

35% to 80% RH(No condensation)

range

A.Value up button

E.Set pressure display area

B.Setting button

F.Output 1 indicator light

C.Value Down button

G.Output 2 indicator light

D.Pressure display area

Model Description

DPS

Measurement range

Output type

N1:NPN

01:-100 to 100kPa

P1:PNP

10:-100 to 1000kPa

Connected mode

NULL:Plug-in

connector.

020:Length 2m

B:Rear End Cable

030:Length 3m

050:Length 5m

Piping specifications

NULL - PT 1/8 with M5 female thread

T - NPT 1/8 with 10-32UNF female thread

G - G 1/8 with M5 female thread

Connection Example

DPSN1:NPN Output

DC(+)-Brown

Load

Out1-Black

Out2-White

DC(-)-Blue

0.8(kPa)

...

DPSP1:PNP Output

DC(+)-Brown

Out2-White

Out1-Black

Load

DC(-)-Blue

28.6

Made in Taiwan

IP64

M5 with female

thread

1.Install the connector

2.Turn on the power

Lead wire

length

(Measurement mode)

Rolling

display

Press the SET button to change menu

Load

12 24V

Rolling

display

Rolling

display

Load

12 24V

Press the SET button to change menu

Hysteresis /window comparator mode

2-M3

Piping specifications:

PT 1/8 with M5 female thread

NPT 1/8 with 10-32UNF female thread

G 1/8 with M5 female thread

User Interface Instructions

(Basic mode)

(Measurement mode)

Press the SET button

for two seconds

Interface switch

Press the SET button

for two seconds

(Basic mode)

Press the value up and

Basic mode

Hysteresis mode

down button to set the

pressure value

Basic mode

Hysteresis mode

Basic mode

Output1-N.O.

Output1-N.C.

Output2-N.O.

2ms、20ms、50ms、100ms、250ms、500ms、1000ms、2500ms、5000ms

Press the value up and

down button to set the

pressure value

Output:Red

Output:Green

No output:Green

No output:Red

Press the value up and

MPa

kPa

down button to set the

pressure value

Press the SET

button to change

psi

1.DC(+) input (Brown)

2.OUT1 (Black)

3.OUT2 (White)

4.Retention(Orange)

5.DC(-) input (Blue)

(Advanced mode)

Press the SET button

for four seconds

Interface switch

Press the SET button

for two seconds

Interface of basic mode

Press the value up and down

button setting the value

Output1

Window comparator

mode

Output2

Window comparator

mode

Output-

Normally open

or close

Output1-N.O.

Output1-N.C.

Output2-N.C.

Output-

Response time

Output-

Color

selection

All-time

display red

display green

kgf/cm

bar

Pressure unit

mmHg

cmHg