Bosch 6 Series Instructions For Installation And Use Manual - Page 17

Browse online or download pdf Instructions For Installation And Use Manual for Dryer Bosch 6 Series. Bosch 6 Series 20 pages. 2 door top freezer, inox-easyclean
Also for Bosch 6 Series: User Manual (24 pages), Instructions For Installation And Use Manual (20 pages), Instructions For Installation And Use Manual (20 pages), Instruction Manual And Installation Instructions (48 pages), Instruction Manual (16 pages), Instruction Manual (48 pages), Installation Instructions Manual (27 pages), Instruction Manual (12 pages), Installation And Operating Instructions Manual (36 pages), Instruction Manual (16 pages), Instructions For Installation And Use Manual (16 pages), Instructions For Use Manual (29 pages), User Manual And Installation Instructions (16 pages), Information For Use (32 pages), Quick Reference Manual (2 pages), Quick Reference Manual (2 pages), Information For Use (28 pages), User Manual (23 pages), Instruction Manual (24 pages), Installation Instructions And Instructions For Use (24 pages), Information For Use (16 pages), User Manual (36 pages), User Manual (32 pages), User Manual (28 pages), User Manual (28 pages), Instruction Manual (28 pages), Information For Use (20 pages), Instruction Manual (28 pages)

Print Page

Bosch 6 Series Instructions For Installation And Use Manual

KGeneral information

E xhaust air mode

G e n e r a l i n f o r m a t i o n

Warning – Risk of death!

Risk of poisoning from flue gases that are drawn back

in. The exhaust air must not be conveyed into a

functioning smoke or exhaust gas flue or into a shaft

which is used to ventilate installation rooms that contain

heating appliances. If the exhaust air is to be conveyed

into a non-functioning smoke or exhaust gas flue, you

must obtain the consent of the heating engineer

responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

The device manufacturer does not assume any

Note:

warranty for complaints attributable to the pipe section.

The device achieves its optimum performance by

■

means of a short, straight exhaust air pipe and as

large a pipe diameter as possible.

As a result of long rough exhaust air pipes, many

■

pipe bends or pipe diameters that are smaller than

150 mm, the optimum extraction performance is not

achieved and fan noise is increased.

The pipes or hoses for laying the exhaust air line

■

must consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the

diameter of the round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

Flat ducts should not have any sharp deflections.

■

Use sealing strips for deviating pipe diameters.

■

Checking the wall

The wall must be level, vertical and adequately load-

■

bearing.

The depth of the bore holes must be the same

■

length as the screws. The wall plugs must have a

secure grip.

The enclosed screws and wall plugs are suitable for

■

solid brickwork. Suitable fasteners must be used for

other structures (e.g. plasterboard, porous concrete,

poroton bricks).

The max. weight of the extractor hood is 40 kg.

■

Electrical connection

Warning – Risk of electric shock!

Components inside the appliance may have sharp

edges. These may damage the connecting cable. Do

not kink or pinch the connecting cable during

installation.

The required connection data can be found on the

rating plate inside the appliance; to do this, remove the

metal mesh grease filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference

suppression regulations.

Warning – Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket that has been

correctly installed.

The mains plug of the mains power cable must be

easily accessible after installation of the appliance. If

this is not possible, an all-pole isolating switch must be

integrated into the permanent electrical installation

according to the conditions of overvoltage category III

and according to the installation regulations.

The permanent electrical installation must only be wired

by a professional electrician. We recommend installing

a residual-current circuit breaker (RCCB) in the

appliance's power supply circuit.