Ativa 516-015 User Manual

Browse online or download pdf User Manual for Power Supply Ativa 516-015. Ativa 516-015 2 pages.

Print Page

516-015

User Guide

OPERATING ENVIRONMENT

32 - 104

F (0 - 40

Computer

Monitor

STATUS INDICATORS, ALARMS and CIRCUIT BREAKER

There are four status indicators (lights) on the front panel of the UPS (On

Line, On Battery, Overload, and Replace Battery).

On Line

On Battery

Overload

Replace Battery

On Line (blue) - is lit whenever utility power is powering the Battery

Backup outlets.

On Battery (yellow) - is lit whenever the battery of the UPS is powering

equipment connected to the Battery Backup Outlets.

Overload (red) - is lit or flashing whenever power demand has exceeded

the capacity of the UPS.

Replace Battery (red) - is lit whenever the battery is near the end of its

useful life, or if the battery is not connected (see above). A battery that is

near the end of its useful life has insufficient run-time and should be

replaced.

CONTENTS

CONNECT BATTERY CARTRIDGE

RJ-11

RJ-45

USB

RJ-45

Coax

ATIVA

CONNECT EQUIPMENT / POWER

Fax

Printer or Scanner

External Disk or

CD / DVD Drive

To 120 VAC Wall Outlet

Four Beeps Every 30 Seconds - this alarm is sounded whenever the UPS is running

On Battery. Consider saving work in progress.

Continuous Beeping - this alarm is sounded whenever a low battery condition is

reached. Battery run-time is very low. Promptly save any work in progress, and exit

all open applications. Shut down the operating system, computer and the UPS.

Continuous Tone - this alarm is sounded whenever the Battery Backup outlets are

overloaded.

Chirps for 1 Minute Every 5 Hours - this alarm is sounded whenever the battery

has failed the automatic diagnostic test.

Circuit Breaker - the circuit breaker button located on the rear panel of the UPS will

stick out if an overload condition forces the UPS to disconnect itself from utility

power. If the button sticks out, disconnect non-essential equipment. Reset the circuit

breaker by pushing the button inward.

CHECK BUILDING WIRING

FAULT INDICATOR

If the rear panel Building Wiring Fault (red) indicator is lit,

a potential shock hazard exists due to one of the following

conditions:

• Open or high resistance ground

• Hot and Neutral polarities are reversed

• Overloaded neutral circuit

Improper building wiring should be corrected by a

RJ-45/

qualified electrician. Do not use the UPS until the

RJ-11

condition that caused the fault is corrected.

Note: Improper building wiring will not prevent the UPS

from operating, but it will limit its protection capability.

Phone

Jack

CABLE IN

CABLE OUT

Building Wiring Fault

Building

Indicator

Wiring

Fault

TRANSFER VOLTAGE and SENSITIVITY ADJUSTMENT

In situations where the UPS or connected equipment appears too sensitive to input voltage, it may be

necessary to adjust the transfer voltage. This is a simple task requiring use of the front panel push

button. To adjust the transfer voltage, proceed as follows:

1. Plug the UPS into the utility power source but do not turn the unit on. The UPS will be in Standby

Mode (no indicators lit).

2. Press and hold the front panel ON/OFF switch fully inward for 10 seconds, until all LED

indicators on the UPS flash to acknowledge it has entered Programming Mode. Release the ON/

OFF button, and the UPS's LEDs will flash per table below, indicating it's current sensitivity

setting.

Note: the UPS automatically exits programming mode in 5 seconds if no buttons are pressed.

3. Use the table below to decide which Sensitivity setting is desired.

Indicators

Sensitivity

Input Voltage

Flashing

Setting

Range

(for utility

operation)

Low

78 - 142 Vac

(yellow)

Medium

88 - 139 Vac

(yellow, and red)

(factory

default)

High

88 - 136 Vac

(yellow, red, and

red)

CONNECT MODEM/PHONE/FAX and

TVSS Ground

If needed, the UPS features a

TVSS ground screw for

connecting the ground lead of

any additional stand alone surge

suppression devices, such as an

From stand alone

ProtectNet product; or any

data line surge

RJ-45/

electronic device with an

suppressor or

external ground connection.

RJ-11

electronic device

RJ-45/

RJ-11

Computer

Modem Port

Phone or Fax

4. To select the Low Sensitivity setting, press and hold the ON/OFF switch

for 1-2 seconds (until a beep is heard). Upon release, the yellow indicator

will flash, indicating Low Sensitivity.

5. To select the Medium Sensitivity setting (the unit's default), press and

hold the ON/OFF switch for 1-2 seconds (until beep is heard). Upon

release, the yellow indicator will flash. Press and hold the ON/OFF

button again for 1-2 seconds (until beep is heard). Upon release, the

yellow and one red indicator will flash, indicating Medium Sensitivity.

6. To select the High Sensitivity setting, press and hold the ON/OFF switch

for 1-2 seconds (until beep is heard). Repeat this two more times. Upon

final release, the yellow and two red indicators (bottom three indicators)

will flash, indicating High Sensitivity.

Use When

7. The UPS will automatically exit Programming Mode in five seconds,

and is ready for use.

Input voltage is extremely low or

high. Not recommended for computer

loads.

UPS frequently goes On Battery.

Connected equipment is sensitive to

voltage fluctuations.

SWITCH ON THE UPS

Note: Allow the UPS to charge for a full or 24 hours prior

to use.

Press the front panel Power ON/OFF switch and observe

that the following events occur after pressing and

releasing the switch:

• The blue On Line indicator flashes.

• The yellow On Battery indicator lights while a Self-

Test is being performed.

• When Self-Test has successfully completed, only the

blue On Line indicator will be lit.

• If the internal battery cartridge is not connected (see

Step 2 above), the blue On Line indicator, and red

Replace Battery indicators will light. The UPS will

also emit a chirping sound.

ON LINE

ON BATTERY

OVERLOAD

REPLACE BATTERY

990-2491