Atlantic Technology SA-350, SA-700 Instruction Manual - Page 7

Browse online or download pdf Instruction Manual for Amplifier Atlantic Technology SA-350, SA-700. Atlantic Technology SA-350, SA-700 16 pages. Inwall subwoofer system for use with atlantic technology iwts-8 sub woofer module only

Print Page

Instruction Manual

Remote Control

Figure 7

Preset Program EQ buttons

Select from 4 preset equalization settings. (page 14)

Reference EQ button

REF button returns the amplifier to its flat/THX EQ settings

and returns the volume trim level to 0dB. (page 14)

MUTE button

Mutes the volume of the amplifier. Pressing again returns the

amplifier to the previous volume setting

Level TRIM buttons

The

button increases and the

ume of the subwoofer above or below the preset reference level

in 1dB increments. (page 14)

button decreases the vol-

Connecting Your Subwoofer

The Atlantic Technology InWall Subwoofer System is simple to hook

up, offering several connection methods for maximum flexibility.

Study the system diagrams starting on Page 8. Once you have found

the example which most closely matches your system, hook up your

subwoofer(s) as shown in that diagram. In all cases, the 8 SUB

Module(s) connect to the amplifier using the SPEAKER OUTPUT(s),

with high-quality speaker wire, as outlined in the High Level Con-

nection section below.

WARNING: To prevent risk of electrical shock or damage to your equip-

ment, always unplug all component AC cords before proceeding with

speaker and component connections! The last step in wiring your sys-

tem should be plugging in the AC cords!

Low Level Connection (LO IN)

We suggest using the low level (RCA jack) subwoofer line out or

preamp output if your receiver/processor has one. This jack may be

labeled Sub, Subwoofer, or LFE (Low Frequency Effects). Simply

connect to the LO IN jack(s) on your SA-350 or SA-700 amplifier

with high-quality shielded cables as shown in Figures 8-10. Please

consult your processor/receiver manual for further information.

Using the Low Level Thruput (THRU)

If your processor has a single subwoofer output and you are using

the SA-700 Dual Mono amplifier connect it using the example in

Figure 9 to connect both channels of the amplifier. We have sup-

plied a short jumper to facilitate this connection method. The THRU

jack(s) can also be used to run a low level signal through the ampli-

fier and out to another unit, as shown in Figure 8. The signal that

comes out of the THRU jack(s) is identical to the input signal.

High Level Connection (HI IN)

Alternately, if you are using the SA-700 with dual 8 SUB Modules,

you may use the high level (HI IN) inputs by following the diagram

in Figure 11. If you do, we recommend that you use high-quality

speaker wire of at least 16 gauge or larger. Please consult your au-

dio/video specialist for more specific information.

IMPORTANT NOTE: You can use the HI IN input on the SA-350 to

connect one high level input from a single channel source. For stereo

(2 channel) hookup, please contact Atlantic Technology for further

information.

You can connect to the HI IN inputs by using a variety of connec-

tors, or by removing 1/2" of insulation from each wire end, twisting

the individual strands of each conductor together, placing the wire

through one of the post holes and screwing down the nut tightly.

It's important to observe polarity while making speaker connections:

red (+) terminals on the amplifier to red (+) on the speaker, black

(–) on the amplifier to black (–) on the speaker. Note that one wire

in each pair will be marked by either the conductor color, printing

on the wire jacket, a ridge on one side of the wire jacket, or a thread

intertwined with the wire strands. By convention, the marked wire

is connected to the red (+) terminal.

Connecting Your Subwoofer