Atlantic Technology SA-380 Instruction Manual - Page 9

Browse online or download pdf Instruction Manual for Amplifier Atlantic Technology SA-380. Atlantic Technology SA-380 12 pages. Inwall subwoofer system thx ultra mono subwoofer amplifier

Print Page

Instruction Manual

Remote Turn-On Using Music Sense

To configure the Model SA-380 so that it will automati-

TRIGGER

cally turn on when the amplifier is receiving an audio

MODE

signal, follow these steps:

MUSIC

Connect the audio input as normal to either the

12V

■

Balanced Input Jack or Unbalanced Input Jack .

Turn the Trigger Mode Switch so that it is in the

■

center position under the word "Music. "

Make sure the AC Power Switch is turned on. The front panel LED

■

will turn amber, indicating that the unit is in the Standby mode,

awaiting a signal that will activate the operational mode.

In this configuration, the Model SA-380 will automatically turn on

whenever it is receiving an audio input signal. The unit will return to the

standby mode a few minutes after the audio signal stops.

Speaker Wire Connections

OUTPUT

the high quality signals produced by your Model SA-380 are carried to

your speakers without loss of clarity or resolution, we recommend that

you use high quality speaker cable. Many brands of cables are available,

your choice may be influenced by a number of factors; i.e.: the distance

between your speakers and the amplifier; the type of speakers you use;

personal preferences; and other factors.

Regardless of the brand or type of cable selected, we recommend using

a cable constructed of fine, multi-strand copper with a gauge of 14 or

larger. Remember, that in specifying cable, the lower the number, the

thicker the cable. Cables with a gauge of 16 may be used for short runs

of less than ten feet. We do not recommend that you use any cables with

an AWG equivalent of 18 or higher due to the power loss and degrada-

tion in performance that will occur.

Cables that are run inside walls should have the appropriate markings

to indicate listing with, and approval by, UL, CSA or other testing agency.

Questions about cables inside walls should be referred to a qualified

installer or a licensed electrical contractor who is familiar with the NEC

and/or the applicable local building codes in your area.

As a general rule, always avoid running input signal or speaker wire con-

nections in parallel with each other, or with AC power cords. This can

result in undesired hum or other interference that will greatly degrade

signal performance.

OUTPUT

MANUFACTURED UNDER LICENSE FROM THX LTD.

THX IS A TRADEMARK OF THX LTD, WHICH MAY BE REGIS-

It is always best to connect the ampli-

fier to your speakers using high quality

cable. The Model SA-380 is equipped

with five-way binding post terminals

that accept bare wire, spade lugs or

banana type plugs (when permitted

MANUFACTURED UNDER LICENSE FROM THX LTD.

by local safety agencies). To assure that

THX IS A TRADEMARK OF THX LTD, WHICH MAY BE REGIS-

The terminals of the SA-380 are designed to allow the use of heavy

speaker wire or connectors. Be sure to tighten them securely, but don't

over-tighten them.

WARNING: To prevent risk of electrical shock or damage to your equipment, always switch

off the amplifiers when making any system connections.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

You can connect your subwoofer to the SA-380 by using a variety of audio

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

connectors such as banana plugs (single or double), pin connectors,

spade lugs, etc; or you may simply use the bared wire itself:

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

1. Remove ½" of insulation from each wire end.

2. Twist the strands of each of the wires together, keeping

the two wires separate.

3. Place the appropriate wire through the hole in the

appropriate connector. This hole is revealed when you

loosen the connector's knob.

4. Screw down the knob firmly to clamp the wire, but be

careful not to over tighten it.

5. Check the tightness of these knobs 24 hours after hookup

and occasionally after that, as they can loosen over

time.

When using any wire connector, follow the manufacturer's assembly and

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

usage instructions. We recommend that you check your local electrical

codes to make sure that you are not using improper connectors (for

example, "banana" plugs are not allowed in some areas).

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

It's important to observe polarity while making speaker connections:

red (+) terminal on the amplifier to red (+) on the speaker, black (–) on

the amplifier to black (–) on the speaker. Look carefully at the wire you

are using and note that one of the conductors of the pair will typically

be identified by color, printing on the outer jacket, ridges on the outer

jacket, or a thread intertwined with the wire strands. By convention, the

marked wire is connected to the red (+) terminal.

Installation and Configuration

INPUT

VOLTAGE

INPUT

VOLTAGE

POWER