Atlantic Ultraviolet MIN-6 Owner's Manual - Page 8

Browse online or download pdf Owner's Manual for Water Filtration Systems Atlantic Ultraviolet MIN-6. Atlantic Ultraviolet MIN-6 16 pages. Germicidal ultraviolet water purifiers
Also for Atlantic Ultraviolet MIN-6: Owner's Manual (16 pages), Owner's Manual (20 pages)

Print Page

–

Step 1

Install Nut on Stud

10.

unprotected 3-prong receptacle is encountered, it must be replaced by a properly grounded Ground Fault Circuit Interrupt

(GFCI) receptacle. Installation must be in accordance with the National Electrical Code and any local codes and ordinances by

a qualified Electrician.

11. Prior to completing the plumbing connection to the water purifier, it is recommended to disinfect the "downstream" plumbing

between the purifier and point of use. This is done by introducing chlorine or other disinfectant solution directly into the

purifier chamber; 100-ppm of chlorine is suggested. With the disinfectant solution in the purifier chamber, turn the germicidal

ultraviolet purifier on. Open the "downstream" outlet until a chlorine or disinfectant solution odor is noticed. Close the outlet

and allow the disinfectant to remain in the plumbing for at least three (3) hours. Flush the plumbing with germicidal ultraviolet

purified water; allow the water to run for a minimum of 5 minutes before use (to ensure no chlorine or disinfectant solution

smell can be detected), this will allow the chlorine or disinfectant solution to be flushed through the pipes.

12.

For added protection, a suitable drain pan must be installed under the purifier. The drain pan must be

plumbed to an adequate, free flowing drain to prevent water damage in the event of a leak. There are numerous leak detection/

flood stop devices, available on the market today, designed to stop the flow of water, reducing the chance of water damage due

to leakage. For more details regarding leak prevention and/or limiting damages due to leaks, please contact

Recommended Options

SENTRY

Safety Sensor (30-0168 or 30-0169): Indicators provide constant visual monitoring of normal operation. In the

event of ballast or lamp failure the safety sensor indicates an alarm condition. The safety sensor is capable of operating an

optional audio alarm and/or solenoid valve.

Promate

Audio Alarm (30-0173A or 35-2099): Activated by the Ultraviolet Monitor or Safety Sensor, alerts the user to

any malfunction detected.

Promate

Time Delay Mechanism (30-1369B or 30-0012B): Provides a 2-minute warm up period during which the

germicidal ultraviolet lamp achieves its full germicidal output before the water is allowed to flow through the water purifier.

The time delay mechanism is used in conjunction with, and is electrically connected to the Solenoid Valve.

4. Promate

Solenoid Valve: Operated in conjunction with the Ultraviolet Monitor, Safety Sensor or Time Delay Mechanism,

this valve prevents water flow through the water purifier when an abnormal condition is detected or in the event of

failure.

SureFLO

Flow Control Valve: Limits water flow to the rated capacity of the purifier. The flow control valve is located in

line prior to the water purifier, and should be protected from germicidal ultraviolet exposure by the use of a 90-degree elbow

fitting between the flow control valve and the water purifier. Unless otherwise specified PVC flow control valves are supplied.

Stainless Steel Flow Control Valves are available for certain models. All PVC and Stainless Steel flow control valves are male

NPT. Consult Factory for other flow control valves.

Promate

Elapsed Time Indicator (30-1008A): A non-resettable display of the water purifier operating hours. Useful for

scheduling and recording maintenance and lamp replacement.

Promate

Safety Glasses (00-1299): Safety eyewear MUST be used as general-purpose safety protection and for additional

shielding from germicidal ultraviolet rays.

Promate

Face Shield (00-0126): Lightweight visor with adjustable headgear provides eye and face protection from

germicidal ultraviolet rays.

NOTE: The recommended options above are available from Atlantic Ultraviolet Corporation

products. For the other devices that may be required for your application, please contact your local water treatment dealer,

plumber or plumbing supplier. If you have any questions, please contact Atlantic Ultraviolet Corporation

by phone or email: (631) 273-0500 – [email protected]

Step 2

Assembly onto Stud & Lock Washer over

Plug ballast into an approved Ground Fault Circuit Interrupt (GFCI) receptacle. Where a 2-prong or

–

Slide Ring Terminal Wire

Ring

–

Step 3

Install Nut on Stud against

Washer & Tighten with 7/16" Wrench

the factory.

or a distributor of their

power