Atlas STRATEGY SERIES FAP42T Installation Instructions

Browse online or download pdf Installation Instructions for Speakers Atlas STRATEGY SERIES FAP42T. Atlas STRATEGY SERIES FAP42T 1 pages. Strategy series ii
Also for Atlas STRATEGY SERIES FAP42T: Brochure (5 pages), General Description (3 pages), Manual (5 pages)

Print Page

FAP42T

Installation

Instructions

Mounting Template

9" Dia.

enclosure. Terminate the service loop to Phoenix style connector provided (please note polarity). Combination

6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg

7. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

9. For safety and seismic considerations a suspension ring is integrated into input panel section of unit. Atlas Sound strongly suggests

that a support wire be installed from this support point to a suitable anchor point above ceiling grid. In drop tile applications, this wire

2. Place tile bridge rails and C-ring through hole. Use V shaped edge of C-ring to align tile bridge assembly above ceiling (alignment screws

3. Bring service loop from through the tile bridge/C-ring to access panel located on side of the enclosure. Terminate service loop to Phoenix style

4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg assemblies until they engage the C-ring assembly.

5. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

Use of optional FAP42-TR

in new construction. Bracket mounts between 16" or 24" OC studs and includes a 3/8" downward lip to provide a template for drywall installers to cut

Note: tile bridge components are not used in new construction applications where new construction bracket is utilized.

1. Bring service loop through hole in ceiling provided by pre construction bracket to access panel located on side of Enclosure.

Terminate service loop to Phoenix style connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.

2. Insert speaker assembly into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dog leg assemblies until they engage

3. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

Input

Auxillary

Suspension

Point

GRILL REMOVED FOR CLARITY

Dog Leg

In Normal

Position

Tile

Bridge

Ceiling Material up to 1

The Atlas Sound Strategy Series

construction drop ceiling or drywall materials

1. Remove 2'x2' or 2'x4' tile.

2. Align adjustable dual rail & c-ring assembly on rear of tile in desired position.

3. Using template provided mark cutout circle with marker and cut hole. (9" FAP42T)

4. Affix C-ring assembly to rails using screws provided and position assembly on rear of ceiling

tile. Replace tile into grid making sure that formed ends of tile bridge rails engage T-bar tile support rails.

5. Bring service loop from rear of tile, through tile bridge C-ring to access panel located on side of

knockouts are provided to facilitate conduit.

assemblies until they engage C-ring assembly. DO NOT OVER-TIGHTEN DOG LEG SCREWS!

8. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.

can usually be installed from an adjacent tile access near speaker location.

Dry Wall ("Hard Deck") Installation

1. Using template provided, mark cutout circle in desired mounting location and cut hole. (9" FAP42T)

provided are not required for this type of installation)

connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.

DO NOT OVER-TIGHTEN DOG LEG SCREWS!

6. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.

New Construction (Darywall Ceilings)

(for use with FAP42T) new construction bracket essentially reserves speaker mounting location prior to drywall installation

around. For final installation, please follow instructions below.

ring provided on new construction bracket. DO NOT OVER-TIGHTEN DOG LEG SCREWS!

4. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.

Typical Parallel Hookup of Full Range 70.7/100V Speakers

Amplifier

Typical 120Watt 70.7V Output

Tap Wattage Total : 64 Watts

master

power

Auxillary

Suspension

1 FAP42-TR Has not been evaluated by UL Laboratories

Point

NOTE: Dog legs will accommodate ceiling material thickness up to 1 1/4" as shipped from factory.

For thicker ceiling materials (up to 2") simply unscrew and flip dog legs as shown.

DO NOT OVER-TIGHTEN DOG LEGS IN EITHER CONFIGURATION!

NOTE: UL recognized conduit clamp must be used for conduit

Dog Leg

connections. Cable connection cavity is not intended to be used

In Inverted

Position

FREQUENCY RESPONSE: 70Hz-20kHz

Ceiling Material up to 2"

II assembly mounts easily into existing

Drop Tile Ceiling

Installation

NOTE: *DO NOT USE 8Ω SETTING WITH 70.7V/100V SYSTEMS! *DO NOT

OVERPOWER IN 8Ω CONFIGURATION! AMPLIFIER OUTPUT SHOULD NOT

EXCEED 16W RMS @ 8Ω PER SPEAKER

Auxillary

Suspension

FAP42T

Point

Full Range

16W @ 70.7V

Dog Leg

as a junction box.

Tile

In Normal

Bridge

Position

SENSITIVITY: 88dB (1W/1M)

Ceiling Material up to 1

ATS001131a RevF 12/08

Installation Instructions

Painting Shield

⁄

" Dia.

FAP42T

Full Range

16W @ 70.7V

Dog Leg

In Inverted

Position

Tile

Bridge

Ceiling Material up to 2"

FAP42T

ATS001131a RevD 2/04

Auxillary

Suspension

Point

Tile

Bridge