Bose Panaray 502A Manual - Page 4

Browse online or download pdf Manual for Speakers Bose Panaray 502A. Bose Panaray 502A 4 pages. Full-range-driver array loudspeakers
Also for Bose Panaray 502A: Technical Information (4 pages), Installation Manual (12 pages), Installation Manual (24 pages), Installation Manual (32 pages)

Print Page

Panaray

Accessories

A full line of accessories has been

specially designed by Bose

the Panaray system components. These

accessories increase system configura-

tion flexibility and provide simple

solutions for typical installation chal-

lenges.

502

A Controlled Array Accessories

• CSB-5A Suspension Bracket (2-point

gravitational type, 0º–45º pitch range)

• WCB-5 U-bracket (for wall/ceiling

surface mounting, ±90º range)

• WBP-5 Bi-Pivot Bracket (single-point

surface mount, 0º–45º pitch, ±80º yaw)

• CVT-5 Constant Voltage Transformer

(70/100 volt distributed system trans-

former and housing)

• PSA-5 Stand Adapter (compatible with

Bose SS-5 and SS-10 stands)

502B Acoustimass

Bass Enclosure

Accessories

• CSB-5B Suspension Bracket (2-point

gravitational type, 0º–30º pitch range)

502C Systems Controller Accessories

• Acoustic Wave

Cannon system option

card for active equalization (not shown)

CSB-5A

Suspension

Bracket

WBP-5

Bi-Pivot

Bracket

PSA-5

Stand Adapter

for use with

CVT-5 Constant Voltage Transformer

CSB-5B

Suspension

Brackets

Engineers' and Architects'

Specifications

502A Controlled Array:

The mid-high frequency device shall be a

multiple-driver system with matched

active equalization as follows:

The transducer complement shall

consist of five (5) high-sensitivity drivers

of 4.5 inches (11.4 cm) diameter,

mounted vertically on a single baffle

assembly such that directional charac-

teristics are optimized for smooth

response.

WCB-5

U-bracket

The input connector, located on the rear

of the array enclosure, shall consist of a

screw-type barrier strip.

The array enclosure shall be composed

of copolymer materials, with outer

dimensions of 23.5" H x 5.75" W x 6.76"

D (59.7 cm H x 14.6 cm W x 17.1 cm D);

its weight shall be 15 lbs (6.8 kg).

The array maximum acoustic output

shall be 112dB SPL from 130Hz to

15kHz, with measurements referenced to

full-bandwidth pink-noise input at 1

meter at the array's rated power. Its

power handling capacity shall be 150

Watts continuous referenced to IEC

noise for 100 hours. The nominal

horizontal beamwidth shall be 120º. The

nominal vertical beamwidth shall be 70º.

The loudspeaker shall be the Bose

Panaray 502A Controlled Array.

502B Acoustimass Bass Enclosure

The low frequency device shall be a dual

ported highly compact enclosure with

matched active equalization as follows:

The transducer complement shall consist

of one (1) high power handling driver of

30 cm diameter, mounted inside an

enclosure such that distortion is mini-

mized as a result of acoustic filtering. Its

operating frequency range shall be below

150Hz so that non-localizability shall

allow a high degree of location place-

ment flexibility.

The input connector, located on the rear

of the enclosure, shall be a screw-type

barrier strip.

The enclosure shall be made of high

strength, high density resin-impregnated

vinyl wrapped particle board, with outer

dimensions of 31.0" H x 14.0" W x 15.5"

D (78.7 cm H x 35.6 cm W x 39.4 cm D);

its weight shall be 85 lbs (38.6 kg).

The bass enclosure's maximum acoustic

output shall be 115dB SPL from 55Hz to

150Hz, with measurements reference to

a full-bandwidth pink-noise input at 1

meter at the enclosure's rated power. Its

power handling capacity shall be 450

Watts continuous referenced to IEC

noise for 100 hours.

The bass enclosure shall be the Bose

Panaray 502B Acoustimass Bass

enclosure.

502C Systems Controller:

The array and/or bass enclosure shall be

supplied with a fixed 2-channel, systems

controller which provides active elec-

tronic equalization and crossover

functions, to be connected before the

input(s) of the system power amplifier(s).

The systems controller shall use screw-

type terminal strips for balanced input

and output wiring connections, and shall

be rack mountable in a single space of a

standard 19" equipment rack.

It shall also include an operating mode

switch,input sensitivity switch, low

frequency output level control, and mono

sum switch.

The electronic controller shall be the

Bose 502C System Controller.

Warranty Information

The Bose Panaray 502A Controlled Array

and the 502B Acoustimass Bass Enclo-

sure, are both covered by a five-year,

transferable limited warranty. The Bose

502C System Controller is covered by a

two-year, transferable limited warranty.

01701-9168 USA JN96508 PN171946-Rev. 1