Bose 2060 Installer's Manual - Page 10
Browse online or download pdf Installer's Manual for Amplifier Bose 2060. Bose 2060 40 pages. Commercial power amplifiers
Print Page
4.0 Operation
4.2 Rear Panel
CAUTION
AVIS
RISK OF ELECTRICAL SHOCK
RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN COVER,
NE PAS OUVRIR CE CARTER,
AUTHORIZED PERSONNEL
RESERVE AU PERSONNEL
ONLY.
AUTORISE.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference which may cause undesired operation.
Complies with Canadian ICES-003 Class A specifications.
120VAC, 4.6A max.
60 Hz
600W
SERIAL No.:
®
Model 2150
D.O.M.:
BOSE CORPORATION
FRAMINGHAM, MA 01701-9168 U.S.A.
MADE IN U.S.A. OF DOMESTIC AND FOREIGN COMPONENTS.
10
7
1
Standard Input Module
2
Input Connectors
3
EQ Out Connectors
Input Modules
1. Standard input module
Through the use of the Bose
fier) and EQ cards, Bose Model 2060 and Model 2150 amplifiers can provide active equal-
ization for Bose Model 8, Model 32, Model 32SE, 402
professional loudspeakers.
Each channel of the input module has its own EQ card input connector, which allows
independent equalization for each channel. For a view of the input module, refer to Figure
31 on page 28.
2. Input connectors
A combination
1
⁄
" TRS/XLR input connector on the input module allows for either a
4
(Tip-Ring-Sleeve) input or a XLR input. The input module quick-connect terminal block is
wired in parallel with the TRS/XLR input connector. This allows for easy connection of
stripped wires to the provided connector. Two parallel input connectors allow for simple
connection of parallel amplifiers. Only one connection per channel can be used.
Note: When using the standard input module in mono mode, use CH 2 input only.
10
CH 2
CH 1
SEQUENCE
REMOTE LEVEL
CH 2
CH 1
SND RCV
COM CH2 CH1 +5V
FX CH 2
SEND
RECV
SEND
+
+
8
6
5
4
Equalizer Present LEDs
5
Speaker Outputs
6
Effects Loop
®
input module (the standard module provided with the ampli-
, 502
®
November 19, 2001
9
Use Class 2 Wiring
For bridged operation.
Consult user manual.
WARNING
RISK OF HAZARDOUS
ENERGY! MAKE PROPER
SPEAKER CONNECTIONS.
SEE OPERATING
INPUT IMPEDANCE 25K OHMS EACH LEG TO GROUND (TOTAL 50K OHMS BALANCED)
MANUAL BEFORE USING.
AVERTISSEMENT
ENERGIE ELECTRIQUE
DANGEREU SE. VOIR
PUSH
LANOTICE
DE FONCTIONNEMENT.
2
1
3
J20018292
FX CH 1
+
2
1
RECV
3
+
+
PN# 1234567
2
7
Dip Switches
8
AC Power Sequence Connector
9
Remote Level Control
10
A, 502B and 802
series II
®
®
SEND
RECEIVE
PUSH
INPUT CH 2
INPUT CH 1
SEQUENCE
EQUALIZATION
2
1
ON
CH1
3
CH2
CH2
EQ. OUT
CH1
4
3
IEC Power Cord
1
⁄
" TRS
4
1
AM259107_00_V.pdf