Anova F1074 Assembly Instructions - Page 2
Browse online or download pdf Assembly Instructions for Indoor Furnishing Anova F1074. Anova F1074 2 pages.
Print Page5. The walls of the concrete base should be vertical and smooth
to minimize the effects of frost upheaval. This can be achieved
with the use of concrete forms, such as Sonotube. Consider
extending the concrete base below the frost line. Consult a
professional for loose or unusual soil conditions.
6. Create a temporary structure that will be used to support the
Adapter/Support Assembly, at the desired height and level,
while the concrete is curing. The depth to install the Inground
Support is dependant on the application: 26.06" depth for
non-ADA installations and tables with 4 seats; 22.94" depth for
ADA compliance (for tables with less than 4 seats) to achieve
the required table clearance.
7. Fill forms with concrete and insert supports, centered in
concrete, until the Adapter/Support Assembly is supported
by the temporary structure. Allow the interior of the Inground
Support to fill with concrete up to the Drain Hole. Crown the
concrete cap to optimize drainage. Allow the concrete to cure
before attaching the Seat Support assemblies.
8. Place one of the seats upside down on the packing cardboard or other soft
work surface. Position one of the Seat Supports so the mounting holes in
the Seat Support line up with the mounting holes on the Seat Frame.
Place one of the 5/16" Washers on one of the 1.25" long Bolts and insert
the Bolt through the Seat Support and Seat Frame mounting holes. Apply a
5/16" Washer and 5/16" Nut to the end of the Bolt and tighten finger tight.
Repeat for the other three mounting holes. After all Bolts are installed, use
the Ratchet with 1/2" Socket and 1/2" wrench to tighten the Nuts.
Attach the remaining Seats to the remaining Seat Supports in the same
manner. Tables may have 2, 3, or 4 seats depending on the model.
9. After the concrete has cured and the installation hole is backfilled, position
two of the Seat Support assemblies on opposite sides of the Inground
Support. Place a 1.375" O.D. Washer onto one of the 5.5" Long Bolts and insert
the Bolt through the mounting holes of the Inground Support and both Seat
Supports. Add a 1.375" O.D. Washer and Nylon Insert Nut to the end of the
Bolt and tighten the Nut finger tight.
Repeat for the other three mounting holes in the Seat Support assemblies.
After all bolts are installed, use the Ratchet with 3/4" Socket and 3/4" Wrench
to tighten the Nuts. Check with a Level and adjust the seat as needed while
tightening. Install any remaining Seat Support assemblies in the same manner.
10. Position the Table top on the Table top Adapter so that the mounting
holes in the Frame of the Table top align with the mounting holes in the
Table top Adapter. Place one of the 5/16" Washers on one of the 1.25"
Long Bolts and insert the Bolt through the Table top Frame and the Table
top Adapter mounting holes. Apply a 5/16" Washer and 5/16" Nut to the
end of the Bolt and tighten finger tight.
Repeat for the other three mounting holes in the Table top and the Table
top Adapter. After all Bolts are installed, use the Ratchet with 1/2" Socket
and 1/2" Wrench to tighten the Nuts. Use a Level while tightening the
hardware and adjust the Table top as needed while tightening.
•
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,
missing, or broken hardware, and general instability.
•
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.
wArnInG
•
Repairs must be made using only factory authorized parts and methods.
cAre AnD
•
Do not drag the assembled unit across any surface.
mAIntenAnce
•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to
remove surface dirt. Do not clean with a solvent or petroleum based products.
211 No
St. Louis, MO 63141
ASI 145
rth Lindbergh Blvd.
Temporary Structure
to hold the Adjuster/
Support assembly vertical
and at correct height for
application
Drain Hole
26.06"
OR
22.94 ADA*
16.00"
5/16" Washer
5/16" Nut
1.25" long Bolt
5/16" Washer
Cardboard
or other soft
work surface
1.375" OD Washer
Nylon Insert Nut
5.5" Long Bolt
1.375" OD Washer
5/16" Washer
5/16" Nut
1.25" Long Bolt
5/16" Washer
tel: 888.535.5005
web: anovafurnishings.com
Ground Level
* Use the 26.06" depth
for non-ADA installations
and tables with four seats.
For tables with less than
30.00"
four seats, to achieve the
required table clearance
for ADA compliance, use
the 22.94" installation
depth.
10/2012