DSC PK5500 Installation Instructions Manual - Page 2

Browse online or download pdf Installation Instructions Manual for Security System DSC PK5500. DSC PK5500 16 pages. Power series
Also for DSC PK5500: Instruction Manual (20 pages), Installation Instructions Manual (9 pages), Installation Instructions Manual (8 pages)

Print Page

DSC PK5500 Installation Instructions Manual

The PK5500 keypad can be used on security systems with up to 64

zones. These keypads are compatible with the latest version of the foll-

lowing DSC security systems:

•PC580

•PC585

•PC1555MX

•PC1616

•PC1832

•PC1864

•PC5008

•PC5010

•PC5015

•PC5020

Specifications

• Temperature range: -10°C to +55°C (14°F to 131°F)

• Humidity (MAX): 93% R.H., non-condensing

• Plastic enclosure protection degree: IP30, IK04

• Voltage rating: 12V

nominal

• Connects to control panel via 4-wire Keybus

• 1 keypad zone input/PGM output*

• PK5500 Current Draw: 50mA (standby)/125mA (maximum)

• Wall mount tamper

• 5 programmable function keys

• Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), A C (Green LED)

• Low temperature sensor: Alarm 6°C (43°F)/Restore 9°C (48°F)

NOTE: * Zone not to be programmed as Fire type or 24h type.

Unpacking

The Power keypad package includes the following parts:

•One Power keypad

•Keypad inner door labels

•Four mounting screws

•1 tamper switch

•2 end-of-line resistors

•Installation Instructions

Mounting

Mount the keypad where it is accessible to designated points of entry

and exit. Once you have selected a dry and secure location, perform

the following steps to mount the keypad.

Disassemble Keypad

1. Insert a flat head screwdriver into the provided slot (first of two).

2. Move screwdriver toward the back plastic and lift as in the following

diagram. This will unhook one side of the front plastic.

3. Repeat step # 1 and 2 on the second provided slot to disconnect

the front plastic and allow access for wiring.

•PC1565

•PC5005

•PC5016

Mount and Wire Keypad

Knock Out

Wiring Slot

Knock Out

Hooks

Knock Out

Tamper

Swing

Hooks

to engage

Tamper

Press to Snap

1. Secure Keypad to wall using mounting holes. Use all 4 screws provided

unless mounting on a single gang box.

2. Place keypad into hooks on the backplate and swing down to engage.

3. Run wire through wiring slot or knockouts. Connect Keybus and PGM/Zone

wiring to keypad. Place tamper switch into tamper hole on backplate.

4. Remove keypad from hooks. Place keypad into backplate, ensure the wire

is pushed back into the wall as much as possible. Route the wire inside

the keypad ensuring high components are avoided. Snap the front assem-

bly closed, ensuring there is no pressure to the keypad from the wire

below.

NOTE: If any tension found between the front keypad assembly

and wiring, please open the keypad reroute the wire and close

again. Repeat these steps until the keypad is closed properly.

Wiring

1. Before wiring the unit, ensure that all power (AC transformer and battery)

is disconnected from the control panel.

2. Connect the four Keybus wires from

the control panel (red, black, yellow

and green) to the keypad terminals.

Refer to diagram.

3. If programmed as an input, you can

connect a device - such as a door

contact - to the "P/Z" terminal of the

To zone or

keypad. This eliminates the need to

PGM output

run wires back to the control panel for

the device. To connect the zone, run one wire from the device to the "P/Z"

terminal and the other wire from the device to the B (black) terminal. For

powered devices, run the red wire to the R (positive) terminal and the

black wire to the B (negative) terminal. When using end of line supervi-

sion, connect the zone according to one of the configurations outlined in

your system's Installation Manual.

4. If the P/Z terminal is programmed as an output, the output follows the

PGM programmed in Section [080]. A small relay, buzzer or other DC

operated device may be connected between the positive supply voltage

and the P/Z terminal (maximum load is 50mA).

Applying Power

Once all wiring is complete, and the equipment is secured to the building

structure with at least two screws apply power to the control panel:

1. Connect the battery leads to the battery.

2. Connect the AC transformer.

For more information on control panel power specifications, see the control

panel Installation Manual.

PK5500

RED

BLK

YEL

GRN