DAITEM SH602AX Installation Manual - Page 6

Browse online or download pdf Installation Manual for Security System DAITEM SH602AX. DAITEM SH602AX 8 pages. 2 function remote keyfob with information feedback, bi-protocol 4 function remote keyfob with information feedback,8 function 4 key remote keyfob with information feedback

Print Page

6. Locking the remote control keyfob via a code

This step only concerns the remote control devices SJ604AX and SJ608AX.
Locking the keyfob via a code prevents it from being used. The "code" corresponds to the keyfob being pressed 4 times
(any key or keys).
When the keyfob is locked, a key can be pressed without any commands being transmitted by radio.
The keyfob can only be unlocked using the code or by putting it back into its factory configuration.
The factory configuration of the locking code involves pressing

6.1 Procedure for locking or unlocking the keyfob

The procedure is identical in both cases.
R
LED off
about 2 s
0.5 s
press as
shown
Simultaneously
The LED lights up
press the
a steady green =
2 bottom keys
the keyfob is
for longer than
ready for the
2 seconds.
correct code to
be entered

6.2 Personalising the locking code

The keyfob must not be locked.
R
LED off
about 2 s
0.5 s
press as
shown
Simultaneously
The LED lights
press the
up a steady
2 bottom keys
green = the
for longer than
keyfob is
2 seconds.
ready for the
correct code
to be entered
(1) Or the factory locking code for a first code change.
IMPORTANT: if you enter the wrong code or if the 5 s code entry time runs out, the LED will flash red.

7. Three-colour LED operation

The viewing of events depends on the devices to be controlled as well as on the type of radio used. Events can only be
viewed on the remote control unit having issued the order and concern the last key pressed (i.e. the last command issued).
IMPORTANT: the LED does not light up when the key has not been allocated with an Optwin
programmed as a "disabled key" (command n° 44) for TwinBand

7.1 Information feedback

Information feedback is displayed when the receiver product acknowledges a command and indicates its status. This
display concerns:
• the TwinBand
®
radio alarm control panel when its system status is modified or queried,
• Optwin
®
wireless products (external receiver or doorphone controller) when these are able to send information about their
status (e.g.: product fitted with a position contact or allocated with a bistable type command like a toggle switch function).
O
O
O
O
0.2 s
Enter the
The LED
locking code by
lights up
pressing 4 times
a steady
on the chosen
green =
key or sequence
the code
of keys
is correct
O
O
O
O
0.2 s
Enter the old
The LED
Simultaneously
locking code (1)
lights up
by pressing
a steady
2 bottom keys
4 times on the
green =
for longer than
chosen key
the code
or keys
is correct
then
then
1 s
IMPORTANT: if you
enter the wrong code
or if the 5 s code
entry time runs out,
the LED will flash red.
The LED lights up
a steady green =
the keyfob is locked
or unlocked
R
O
about 2 s
0.5 s
The LED
Enter the new
press the
lights up a
locking code by
steady green
pressing 4 times
= the keyfob
on the chosen
2 seconds.
is ready for
key or sequence
the new
code to be
entered
®
radio.
6
and then
.
R
red LED
O
orange LED
green LED
O
O
O
1 s
R
red LED
O
orange LED
green LED
The LED lights
up a steady
green = the new
code has been
correctly
of keys
programmed
®
radio link or if it has been